RotoMetals2Inline FabricationStainLess Steel MediaRepackbox
MidSouth Shooters SupplyWidenersGraf & Sons

Tab Content
  • poppy42's Avatar
    12-11-2018, 03:55 PM
    Chinese plastic takeout food containers!
    31 replies | 592 view(s)
  • poppy42's Avatar
    12-11-2018, 12:09 AM
    poppy42 replied to a thread Pif in Pay It Forward
    I don’t know if this is still available. If it is I can definitely use it. Pm on the way
    4 replies | 321 view(s)
  • poppy42's Avatar
    12-07-2018, 10:33 PM
    Over the years I’ve had several instances were I had to contact Lee customer service! They have always, and I repeat always! Taken excellent care of me! They have replaced broken parts without question( oh by the way they were broken due to improper...
    36 replies | 941 view(s)
  • poppy42's Avatar
    11-28-2018, 08:36 PM
    poppy42 replied to a thread No RTV. Do I dare. in Our Town
    Sorry I guess I read a post wrong. Hey I’m old give a break. Anyway good luck with the rebuild and please post some pics of that truck
    40 replies | 1644 view(s)
  • poppy42's Avatar
    11-28-2018, 08:19 PM
    poppy42 replied to a thread No RTV. Do I dare. in Our Town
    The fact That the valve covers and Oil pan and similar parts and gunk on inside. The last time the engine was rebuilt it’s very possible they didn’t bother the clean those things adequately. Just changed the parts that were broken worn out and...
    40 replies | 1644 view(s)
  • poppy42's Avatar
    11-28-2018, 07:44 PM
    poppy42 replied to a thread No RTV. Do I dare. in Our Town
    No rtv on head gaskets or valve covers or just about any place on that motor. On On places like thermostat housing’s maybe oil pans where gaskets are tough to hold in place I would put a little gasket shellac on one surface only! usually on the...
    40 replies | 1644 view(s)
  • poppy42's Avatar
    11-28-2018, 03:18 PM
    First off I would place each face of the mold on a known, flat surface. Such as a drill press table, milling machine table, or something that you know is flat. I would then checked for abnormalities on each face of the mold. More than likely...
    5 replies | 340 view(s)
  • poppy42's Avatar
    11-28-2018, 12:31 AM
    I’m new to the 310 and I’m looking for a 9 mm set. Pm on the way
    5 replies | 273 view(s)
  • poppy42's Avatar
    11-22-2018, 08:42 PM
    Well itís been an interesting year. I still havenít had a meaningful conversation with my son in over a year but thatís OK the ball is in his court and I see my granddaughterís . Financially speaking mayor will leave that one alone other than to...
    6 replies | 259 view(s)
No More Results
About poppy42

Basic Information

About poppy42


Long, Wide, Deep, and Without Hesitation!


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 12:42 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check