ADvertise hereStainLess Steel MediaMidSouth Shooters SupplyInline Fabrication
Titan ReloadingRotoMetals2Graf & SonsLee Precision

Tab Content
  • dimaprok's Avatar
    03-08-2018, 05:12 PM
    So if you are able to achieve MOA groups with spread of 0.2 grains on the heavy side i need to stop sorting within .02 grain batches. My total spread would be under .1 grain. Sent from my SM-G950U1 using Tapatalk
    9 replies | 301 view(s)
  • dimaprok's Avatar
    03-05-2018, 03:44 PM
    Actually to be honest I forgot about that, thanks for pointing out. It's been 2 years since I build mine and I don't remember details. I probably got SNR version because I just used 110v AC to power it and I don't use any other power supplies. I...
    45 replies | 975 view(s)
  • dimaprok's Avatar
    03-05-2018, 02:40 PM
    I am using this one, works great for 2 years. They are all made in China. No problems with cold solder joints. Free 2 day prime shipping. $20, you can buy two for less than 1 Auberins. Dual Display Manual/ Auto-tuning PID Temperature...
    45 replies | 975 view(s)
  • dimaprok's Avatar
    03-03-2018, 06:35 PM
    I build mine for about 30 - 35 bucks. You don't need to order your controller from expensive online company, I got mine from Ebay or Amazon. I also didn't use screw terminal although it will make job easier. Had it now for 2 years and when I...
    45 replies | 975 view(s)
  • dimaprok's Avatar
    03-03-2018, 06:24 PM
    my home build PID doesn't have this problem unless there is 1/2" lead at the bottom. Sent from my SM-G950U1 using Tapatalk
    45 replies | 975 view(s)
  • dimaprok's Avatar
    02-28-2018, 04:03 AM
    Made it for 30 caliber and they seat really good although on really hard lead alloy when seating and resizing with Lee sometimes I get a bit of a "lip" perhaps it could be a hair smaller otherwise it's great! I made a video:...
    106 replies | 53162 view(s)
  • dimaprok's Avatar
    02-27-2018, 06:09 PM
    So you broke the lever trying to open sprue blade and you still haven't learned a thing that mold needs to be pre-heated? Preheating does not cause any tear out, but what it does helps you to start casting pretty much right away without dumping 1/3...
    27 replies | 644 view(s)
  • dimaprok's Avatar
    02-22-2018, 08:13 PM
    Crimp is flaring case mouth? what??? that doesn't make sense. Also "trimming" shell plate one or two thousands of an inch won't make any difference whatsoever. I would say start with 10 thousands. Plunk test for 300 blk? My understanding...
    14 replies | 269 view(s)
  • dimaprok's Avatar
    02-22-2018, 06:23 AM
    I ordered my 1st Lyman mold from midwayusa because it was on sale in 22 cal and it had one cavity in the nose with a groove like a chip that got welded to the cutter and scratched out a groove, pretty obvious with a naked eye. I decided to cast...
    33 replies | 896 view(s)
  • dimaprok's Avatar
    02-21-2018, 01:17 AM
    So over the weekend i decided to test it the flattening with the hammer- it passed. I am still seeing little chips of PC missing but now I know it has to to be something else perhaps bullets falling from the tray and on the way to bucket hitting...
    24 replies | 844 view(s)
No More Results
About dimaprok

Basic Information


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 03:12 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check