Lee PrecisionGraf & SonsInline FabricationRotoMetals2
Wisconsin TriggerMidSouth Shooters SupplyTitan ReloadingStainLess Steel Media

Tab Content
  • Harry Tobin's Avatar
    Yesterday, 07:58 PM
    Which 200 swc mold you have? 452-200-SWC.............................. TL452-200SWC I had both styles and the first was the tumble lube type and that went junk pile. Then I got the 1 groove...
    12 replies | 273 view(s)
  • Harry Tobin's Avatar
    Yesterday, 04:47 PM
    Harry Tobin replied to a thread Reloads and smoke in Cast Boolits
    What about that Ben's Red I've seen here. It has high temp grease in it, would that hold down some smoke?
    18 replies | 372 view(s)
  • Harry Tobin's Avatar
    Yesterday, 12:58 PM
    Harry Tobin replied to a thread Reloads and smoke in Cast Boolits
    Thatís still confusing to me, when I did my test the New Unique burned slower than the Old Unique was a lot faster. New Unique was 4.1 seconds and Old Unique was 2.6 seconds, I would think with nitro glycerin added to the New wouldnít it burn...
    18 replies | 372 view(s)
  • Harry Tobin's Avatar
    Yesterday, 11:38 AM
    Harry Tobin replied to a thread Reloads and smoke in Cast Boolits
    Hi JonB, I just like trying stuff and it funny you where talking about the new Unique VS old Unique. There is a difference between the two, I did a burn test with some different powders and those 2 Unique powders were done also. Between the two new...
    18 replies | 372 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 07:58 PM
    So awhile back me and my buddy where talking about reloads and smoke so I did a little test. There are a lot of factors but at least this was a start for me. So I did a short video on this If this needs to be moved that’s OK Harry ...
    18 replies | 372 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 07:51 PM
    Thanks for your reply, not quite what I was looking for so I’ll post it here and if it needs to be moved that’s OK Harry
    6 replies | 152 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 07:26 PM
    I sent a message to a mod and didnít here back yet. But is there a place here where folks talk about reloading, such as powders, types of powders and charges? If there is I just couldnít find it.
    6 replies | 152 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 04:25 PM
    Thanks guys your hospitality has been great here. Necessity is the mother of invention is the way I look at it and if you own it know how to fix it. I like sharing my ideas if it helps anyone, and sometimes I just want to know more. Just watched...
    15 replies | 282 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 11:57 AM
    That sounds so familiar, some years back I had a real bad leading problem when shooting either my 1911 or 9mm. A day at the range with 150 rounds of fun turned into a 2 hour barrel clean out. At first I thought it was a harness problem but then...
    7 replies | 281 view(s)
  • Harry Tobin's Avatar
    03-22-2017, 10:27 AM
    Thanks guys for the warm welcome, the older I get the more I want to know! It’ll take sometime to get to know folks here. I did put up my first post in The Star Equipment Corner about the bullet feeder I made. Just trying to pass on some info if...
    11 replies | 242 view(s)
  • Harry Tobin's Avatar
    03-21-2017, 02:09 PM
    Hey guys well Iím the new guy on the block here but want to show you my homemade bullet feeder for my star. I started this last summer trying to get all the ideas that I could use from base down feeders and trying to figure out the process of...
    15 replies | 282 view(s)
  • Harry Tobin's Avatar
    03-20-2017, 08:18 PM
    You are correct it’s a Tork box, I’m over overwhelmed with the talent on this forum. But sometimes small ideas work also
    6 replies | 207 view(s)
  • Harry Tobin's Avatar
    03-20-2017, 03:54 PM
    Hi folks this is my first post here, just wanted to give back to this site. Without seeing all the smart guys here I wouldnít have got my pid made. Built that 2 years ago, works great in the lead pot and also works for the heated base on my star....
    6 replies | 207 view(s)
  • Harry Tobin's Avatar
    03-20-2017, 01:52 PM
    About half way between quakertown and doylestown Doesn't look like your that far away, I go shooting at branch valley gun club
    11 replies | 242 view(s)
  • Harry Tobin's Avatar
    03-20-2017, 01:32 PM
    Hi guys just wanted to introduce myself. I finally signed up for cast boolits after all this time. So Iím the new old guy on the block, I love to shoot and reload and make some things along the way. Now my gun forum is good but no one really gets...
    11 replies | 242 view(s)
No More Results

Statistics


Total Posts
Total Posts
13
Posts Per Day
3.05
General Information
Last Activity
Yesterday 08:05 PM
Join Date
03-19-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check