Inline FabricationStainLess Steel MediaLee PrecisionADvertise here
MidSouth Shooters SupplyRotoMetals2Titan ReloadingGraf & Sons

  • adam_mac84's Avatar
    Yesterday, 08:35 PM
    Interestingly enough. I been running 3.8gr TG all summer Also. Is WDRS with tin added Sent from my iPhone using Tapatalk
    1 replies | 75 view(s)
  • adam_mac84's Avatar
    Yesterday, 08:33 PM
    Brought 11 (actually 9) loads of 10 rounds to the only indoor range within an hour that allows CB (2 'test' loads of 5 I figured were a bit hot... no pressure seen tho). I am not extremely familiar with shooting off of a rest, one of the janky...
    1 replies | 75 view(s)
  • adam_mac84's Avatar
    01-16-2018, 07:52 PM
    I like this plan. I was just hoping to avoid the unnecessary leading (and save buying 3 different sizers). I appreciate all of the responses
    12 replies | 464 view(s)
  • adam_mac84's Avatar
    01-14-2018, 09:22 AM
    35rem. Thanks. My measurement was groove diameter. The slug was certainly over barrel diameter. I drove through end of barrel and shaved a ring all the way around the slug before it drove completely into barrel. I would say it was probably at least...
    12 replies | 464 view(s)
  • adam_mac84's Avatar
    01-13-2018, 12:03 PM
    That was the widest diameter. It was AC Range scrap. Is what I had access to. Cast in a spent 45 case. Sent from my iPhone using Tapatalk
    12 replies | 464 view(s)
  • adam_mac84's Avatar
    01-12-2018, 03:08 PM
    Slugged my ATI 1911 at .448. Seems odd to be undersized versus oversized. Used calipers with multiple careful measurements. Going to have my machinist Neighbor verify with his better micrometer. Gunna run .450 sizer after PC. Doubt I can run as...
    12 replies | 464 view(s)
  • adam_mac84's Avatar
    01-10-2018, 07:17 PM
    Dog, didn't see one, sent you PM, but following up here in case there is some problem with PM :edit: MB was full
    2 replies | 287 view(s)
  • adam_mac84's Avatar
    01-09-2018, 07:48 PM
    Never fired. I did dry test fire with a snap cap 4x as pictured. I included photo of instructions. States fits 70/80 Series 1911. Full size 1911. $175obo. Or trade for 45ACP casting/reloading equip. (Prefer Lee) Payment prefer PayPal F/F. ...
    2 replies | 287 view(s)
  • adam_mac84's Avatar
    01-05-2018, 10:17 PM
    Got my PID wired and tested. Now just have to get it mounted in a metal box... Holding 700* nearly perfectly
    5523 replies | 442949 view(s)
  • adam_mac84's Avatar
    12-24-2017, 08:10 AM
    Itís a zev barrel. Consequently my Glock Barrel does not lead. I am just saving it. For. Something I guess. Haha. (Zev was a near gift price so I run it) Sent from my iPhone using Tapatalk
    9 replies | 637 view(s)
  • adam_mac84's Avatar
    12-23-2017, 08:44 PM
    Sitting in my bench I have 100 test loads in various configurations to work up an ‘accuracy’ load. My current is set to min PF for competing and is good enough for alpha/Charlie work. So I take my BIL, the Gunny to a local range with a bunch of...
    9 replies | 637 view(s)
  • adam_mac84's Avatar
    12-20-2017, 09:10 PM
    I am trying to play the percentages this week on a snow melt to try to get to the club to snag some other people's brass that has been covered and uncovered by snow/melt. :veryconfu
    32 replies | 1370 view(s)
No More Results
About adam_mac84

Basic Information

About adam_mac84
Location:
w michigan

Statistics


Total Posts
Total Posts
196
Posts Per Day
0.59
General Information
Last Activity
Today 01:57 PM
Join Date
02-19-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check