RotoMetals2MidSouth Shooters SupplyLee PrecisionInline Fabrication
ADvertise hereRepackboxTitan Reloading

Tab Content
  • nhyrum's Avatar
    01-05-2021, 10:51 PM
    I mean... A 2013 toyota van to a 2021 toyota van IS an upgrade. Not a "step up" but an upgrade, I think so. Doesn't mean the newer model is all around better in every way. It's like the 550 models. The 750 is basically just a 650b Sent from...
    16 replies | 609 view(s)
  • nhyrum's Avatar
    01-05-2021, 08:38 PM
    That could be possible, but they'd probably need to be printed in nylon, which is... Tricky, from what I hear. And probably custom modeled, which is above my car skills. If it's not square or round, I'm toast maybe someone else could offer more...
    7 replies | 334 view(s)
  • nhyrum's Avatar
    01-04-2021, 01:24 AM
    It's pretty easy to disactivate the priming advance system... It's just one Allen screw. And it's pretty easy to manually advance And I use almost exclusively federal primers, and never a kaboom. Sent from my SM-G975U using Tapatalk
    16 replies | 609 view(s)
  • nhyrum's Avatar
    01-03-2021, 07:15 PM
    There's a few little differences. The two "big" ones that I remember are the 750 is a touch taller, to accommodate longer oal's, and it uses a linear priming system, more akin to the 550, instead of the rotary priming system of the 650 Sent from...
    16 replies | 609 view(s)
  • nhyrum's Avatar
    12-28-2020, 08:05 PM
    If I had a 45-70 I would be in. Think that might be too heavy got 458 socom too. Sent from my SM-G975U using Tapatalk
    5 replies | 223 view(s)
  • nhyrum's Avatar
    12-28-2020, 04:47 PM
    Ah. Gotcha. Carry on *sulks back into the shadows* Sent from my SM-G975U using Tapatalk
    5 replies | 223 view(s)
  • nhyrum's Avatar
    12-27-2020, 10:47 PM
    I believe there's two up. A 210 ish grain and a 350 ish grain Sent from my SM-G975U using Tapatalk
    5 replies | 223 view(s)
  • nhyrum's Avatar
    12-27-2020, 05:48 PM
    Not doubting that one bit. Same with my mihec moulds. The noe wasn't even as expensive as I was expecting Sent from my SM-G975U using Tapatalk
    5 replies | 239 view(s)
  • nhyrum's Avatar
    12-27-2020, 05:11 PM
    I haven't used any noe molds, do they use the Lee handles? I wouldn't call it really THAT expensive. Compared to my mihec 6 cavity brass ones. It does look like they have a 4 cavity offering, which will be a lot nicer than the 2 cavity Lee. Sent...
    5 replies | 239 view(s)
  • nhyrum's Avatar
    12-27-2020, 02:39 AM
    I was getting excited to try the Lee 209-230, but was on back order, expected stock was mid December. Been getting pushed back and back, blah blah blah. I get it though... Now, expected stock is February... So. I'm looking to see, hope, beg, etc...
    5 replies | 239 view(s)
No More Results
About nhyrum

Basic Information

Date of Birth
September 13, 1990 (30)

Statistics


Total Posts
Total Posts
272
Posts Per Day
0.19
General Information
Last Activity
Yesterday 11:34 PM
Join Date
01-24-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check