ADvertise hereInline FabricationStainLess Steel MediaRotoMetals2
Graf & SonsTitan ReloadingLee PrecisionMidSouth Shooters Supply

Tab Content
WJP's Activity
About Me
Tab Content
  • WJP's Avatar
    03-24-2018, 10:48 PM
    WJP replied to a thread Hopkins and Allen 922 in Single Shot Guns
    Must be loosing my mind.or they added some parts in the past month. Thanks for the link. I'm going to see what a fellow member comes up with this week. I like the little guns and Stevens. Really need to make it cost effective to be a worthy project...
    9 replies | 332 view(s)
  • WJP's Avatar
    03-24-2018, 12:33 PM
    Yes, those are some things to watch for as well as increased erosion due to high temps. Also I personally would not want to run one that hot. You could get close to it's failure rate within another mag or two if you're already over 700. A good...
    47 replies | 1360 view(s)
  • WJP's Avatar
    03-24-2018, 10:13 AM
    WJP replied to a thread Hopkins and Allen 922 in Single Shot Guns
    I thought about selling just so I could find the parts. Thanks for the heads up on the changes NoZombies mentioned that to me as well. All I know is it's a Enders Royal Dead Shot. May not be worth rebuilding but I figured I'd try. I keep checking...
    9 replies | 332 view(s)
  • WJP's Avatar
    03-24-2018, 09:46 AM
    I know what the little c is. I also know how hot they get after running them. One full auto mag dump on a 90 degree got a titanium can to 719 degrees. Most manufacturers rate them at semi, limited full auto for a reason. Glad you made it that long....
    47 replies | 1360 view(s)
  • WJP's Avatar
    03-23-2018, 07:42 PM
    https://www.amt-advanced-materials-technology.com/materials/titanium-high-temperature/
    47 replies | 1360 view(s)
  • WJP's Avatar
    03-23-2018, 12:07 AM
    I've got a nice receiver and barrel but nothing else. Does anyone have an idea who may have some parts? I know I could probably buy one cheaper done than fixing this one but I hate to get rid of it or have it taking up room until I die. I need all...
    9 replies | 332 view(s)
  • WJP's Avatar
    03-22-2018, 11:52 PM
    Glad you found one you like. Be warned not to run it hot. Titanium is light but weakens with heat. So no quick mag dumps, bump fires, full auto, etc. I have a Ti can and love it for my bolt/hunting guns but it doesn't see much over 5-10 rounds in a...
    47 replies | 1360 view(s)
  • WJP's Avatar
    03-21-2018, 05:55 PM
    WJP replied to a thread WTB 7mm stw brass in Swappin & Sellin
    I don't have a lot but have a few stw and maybe some 8mm. I'll check later.
    3 replies | 139 view(s)
  • WJP's Avatar
    03-21-2018, 10:37 AM
    It will be quite a bit. Also before you thread your barrel I would check the twist. You may still end up with a new rifle. I'll need to double check but if you are talking the 175 gr boat tail subs in a 1:12 they work but are on the low end of...
    47 replies | 1360 view(s)
  • WJP's Avatar
    03-21-2018, 09:56 AM
    He was probably trying to sell you a 223 because he needs to move them. Most people nowadays don't run 223 cans. I would go 30 cal and run it on both. I believe extreme shock made some 100 gr subs a while back. I run a 223 only because it is better...
    47 replies | 1360 view(s)
No More Results
About WJP

Basic Information

Statistics


Total Posts
Total Posts
159
Posts Per Day
0.35
General Information
Last Activity
Today 05:22 PM
Join Date
01-23-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check