Lee PrecisionADvertise hereTitan ReloadingWideners
MidSouth Shooters SupplyRepackboxInline FabricationRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 3655 USD (61%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


  • Gewehr-Guy's Avatar
    08-05-2020, 03:18 PM
    You got me thinking about how to install bases on that thin shroud, maybe you could drill and tap a section of thicker walled pipe, and attach a sectioned piece on top of the shroud. Solder, or maybe even Locktite or Acraglass, that could be...
    5 replies | 232 view(s)
  • Gewehr-Guy's Avatar
    08-03-2020, 01:00 PM
    Thanks for the link. I've been shooting a 1889 and a 96/11 some lately, and found some nice loads, so I just ordered a mount for the 1889, and if it shoots as well as I suspect it will, I might get the diopter sights as well.
    5 replies | 241 view(s)
  • Gewehr-Guy's Avatar
    08-03-2020, 12:45 PM
    Is that a Commission 88 ? I would think the barrel shroud is pretty thin to hold the base screws, unless you used silver solder and screws. Also you would need to bend the bolt, or find a carbine bolt.
    5 replies | 232 view(s)
  • Gewehr-Guy's Avatar
    08-03-2020, 12:37 PM
    Gewehr-Guy replied to a thread Chinese Seeds in Our Town
    Waksupi, that made me laugh! But on a serious note, I hope it doesn't give the Gov't the idea that we need strict supervision on what and where we can plant, we can't be letting just anyone plant a garden on their ground, without permission and...
    18 replies | 575 view(s)
  • Gewehr-Guy's Avatar
    07-30-2020, 07:49 AM
    I like Re-7 in the 30-06, around 23gr shoots well with most bullets I've tried, use more if a hunting load. Re-7 is one powder I like to keep a good supply of, because they have dropped it once, and brought it back,might not come back if it goes...
    9 replies | 286 view(s)
  • Gewehr-Guy's Avatar
    07-29-2020, 08:15 AM
    I wanted to do something similar with some 30-06 cases to make some gallery loads, and sized them down in a 270 die, then used a 30 cal. NOE neck expander to seat a round ball. It worked, but necks were not very coencentric.
    12 replies | 480 view(s)
  • Gewehr-Guy's Avatar
    07-29-2020, 08:03 AM
    Gewehr-Guy replied to a thread Sharpening Steel in Our Town
    I remember having a Rev-O-Nok? steel, and a very large F. Dick with German silver ferule and a swivel and small chain on the handle. Both looked to be of superior quality,haven't seen them in years. Now I use a plastic handled cheap looking one,...
    20 replies | 691 view(s)
  • Gewehr-Guy's Avatar
    07-22-2020, 01:56 PM
    I had the same problem with mine a while back, and they sent me parts right away. That being said, I believe the nylon gear problem will be a recurring thing, too large a shaft, and not enough nylon thickness between the gear teeth.
    9 replies | 295 view(s)
  • Gewehr-Guy's Avatar
    07-19-2020, 01:01 PM
    That deserves some further investigation. Does it dry after a light coat?
    9 replies | 430 view(s)
  • Gewehr-Guy's Avatar
    07-17-2020, 12:52 PM
    Well guys, it's obvious it died of Covid-19
    30 replies | 955 view(s)
  • Gewehr-Guy's Avatar
    07-16-2020, 09:45 PM
    On the subject of primer shortages, I read in a WW2 era Rifleman magazine where they were short of LR primers, but could still find a few SP primers. So they removed the anvil, flattened out the pin strike and inserted the small primer inside the...
    27 replies | 1640 view(s)
  • Gewehr-Guy's Avatar
    07-15-2020, 12:46 PM
    Outpost 75, any pictures of one of those powder cannisters, and where on earth did you find something that old ? As to the storage life, didn't Winchester advertise about the stability of their line of Ball powders way back when. I think double...
    7 replies | 387 view(s)
  • Gewehr-Guy's Avatar
    07-11-2020, 05:45 PM
    Looks like the Bond measure, page 199 in Sharpe's Complete Guide to Handloading.
    10 replies | 509 view(s)
  • Gewehr-Guy's Avatar
    07-09-2020, 06:00 PM
    I would assume that all the Swedish rifles used the # 1 action on all their models, so if you can find an advertisment of Remington Rifles, I'm sure they offered the biggest cartridges that would fit, trying to keep pace with their main competition,...
    55 replies | 2657 view(s)
No More Results
About Gewehr-Guy

Basic Information

Statistics


Total Posts
Total Posts
636
Posts Per Day
0.48
General Information
Last Activity
Today 12:11 AM
Join Date
12-14-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check