WidenersMidSouth Shooters SupplyStainLess Steel MediaInline Fabrication
Titan ReloadingLee PrecisionRotoMetals2Graf & Sons
Repackbox
Tab Content
  • Kenstone's Avatar
    10-10-2018, 12:48 PM
    Take a close look at the sleeve where the lever arm contacts it, it's a knife edge, something I rounded off to get a smoother action. That and the lever being a stamped part also has a knife edge where it contacts/activates the sleeve. The edge...
    21 replies | 1168 view(s)
  • Kenstone's Avatar
    10-01-2018, 08:10 PM
    I decap/deprime pistol using my drill press, faster than a reloading press Centering fixture is 2 stacked fender washers, with the top one having a rim diameter hole, mounted on a 1x4. The bottom 2x4 has a big hole to collect the spent primers....
    140 replies | 18260 view(s)
  • Kenstone's Avatar
    09-28-2018, 11:37 PM
    Kenstone replied to a thread Small Clamps in Reloading Equipment
    Just put a shim/spacer both sides of the small end of said taper... A pic of what you are clamping would help a lot here, just sayin' :mrgreen:
    18 replies | 443 view(s)
  • Kenstone's Avatar
    09-28-2018, 10:35 PM
    Kenstone replied to a thread Small Clamps in Reloading Equipment
    What about Binder Clips...come it many sizes/colors, and are cheap. I use them a lot, get the size that'll work, clip/clamp it on, then REMOVE the wire handle things. ...
    18 replies | 443 view(s)
  • Kenstone's Avatar
    09-23-2018, 09:03 PM
    OK I bit the bullet and bought a Frankford Arsenal wet tumbler kit after vibe tumbling forever. I knew there'd be a learning curve but those iddy-biddy pins end up everywhere and I thought I'd need to buy more soon, at the rate I was "loosing"...
    31 replies | 1379 view(s)
  • Kenstone's Avatar
    09-19-2018, 11:46 PM
    I like that steel riser/flip mount. I've made something similar out of 2x6. Basically a box with the top over hanging in the front and the bottom extended out the rear. With some deck screws and wood glue, you could probably make three of them...
    40 replies | 2792 view(s)
  • Kenstone's Avatar
    09-19-2018, 12:35 PM
    You can use low carbon steel and case harden it with this stuff: https://www.brownells.com/gunsmith-tools-supplies/metal-prep-coloring/color-case-hardening/surface-hardening-compound-sku083000033-27119-52952.aspx?rrec=true I've made small wood...
    42 replies | 1338 view(s)
No More Results
About Kenstone

Basic Information

About Kenstone
Location:
Boysee

Statistics


Total Posts
Total Posts
193
Posts Per Day
0.27
General Information
Last Activity
Today 07:32 PM
Join Date
11-06-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check