Inline FabricationLee PrecisionADvertise hereGraf & Sons
RotoMetals2StainLess Steel MediaMidSouth Shooters SupplyTitan Reloading

Tab Content
  • Kenstone's Avatar
    02-17-2018, 04:51 PM
    Sorry I have to ask because you didn't mention it...Are you using the SMALL drum? :-|
    42 replies | 740 view(s)
  • Kenstone's Avatar
    02-14-2018, 10:20 PM
    Kenstone replied to a thread Homemade? in Reloading Equipment
    Not for ammo production/reloading, but more ammo consumption :oops: I bought the paddles and pivot tubes off ebay for $70. The tree trunk is 1-1/2 x 1/4 angle iron tipped forward 20 degrees. The legs are 1" x 1/8 angle iron and the base it 1/4"...
    762 replies | 450151 view(s)
  • Kenstone's Avatar
    02-14-2018, 06:37 PM
    Here's pics of just the clamp: Top Bottom :mrgreen:
    11 replies | 372 view(s)
  • Kenstone's Avatar
    02-14-2018, 01:09 PM
    Use a counter-bore with a cut diameter the size you want the finished hole. Make/turn a pilot for the c'bore the diameter of the current hole. It will follow the pilot and cut the hole to the proper size, even with an extension. :mrgreen:
    13 replies | 492 view(s)
  • Kenstone's Avatar
    02-13-2018, 05:44 PM
    Dan: I'm having trouble visualizing your fix, could you post a pic? 1st pic is of the auto-disc PM base where you can see the shiny spots I filed down until they were flush with a disc to tighten/eliminate the gap between the disc and seal, so...
    11 replies | 372 view(s)
  • Kenstone's Avatar
    02-09-2018, 12:36 PM
    I tracked the leakage om my auto disc to the uneven pressure on the seal. When I tightened the off-center screw that holds the hopper on, it cocked the hopper. That created uneven pressure on the seal and powder leakage. I made a parallel clamp...
    11 replies | 372 view(s)
  • Kenstone's Avatar
    02-09-2018, 11:49 AM
    ...or make a conversion top plate/press head that accepts the "old" 4 die Turret or something similar but the bolt circle of the dies would need to be the same. :popcorn:
    28 replies | 947 view(s)
  • Kenstone's Avatar
    02-09-2018, 03:47 AM
    These get good reviews, R8 spindle, no plastic gears or tilt column: https://littlemachineshop.com/products/product_view.php?ProductID=3990&category=1387807683 With DRO's:...
    34 replies | 1934 view(s)
  • Kenstone's Avatar
    02-07-2018, 12:23 PM
    Bought this HF lathe to make a MC part sold online for about 1/2 the cost of the lathe. So I made 3 parts and sold the other 2 to pay for the lathe. I have operated lathes of all sizes in a former life and knew what I was in for though. I had...
    29 replies | 1380 view(s)
  • Kenstone's Avatar
    01-28-2018, 01:50 PM
    Why not just buy a plate for 9mm for $35 and copy it for 45ACP: https://www.ebay.com/sch/i.html?_odkw=Hornady+LnL+case+feeder+parts&_osacat=0&_from=R40&_trksid=m570.l1313&_nkw=case+feeder+plates&_sacat=0 :mrgreen:
    30 replies | 1302 view(s)
  • Kenstone's Avatar
    01-23-2018, 10:20 PM
    OK, 4 pages in I have to ask, what constitutes the "NEW" Loadmaster? At Titan I've read of the updates to the 2018 Pro 1000 being an index pin/steel base and primers exiting thru the ram, but nothing in the way of up-grades to the Load Master......
    136 replies | 4714 view(s)
  • Kenstone's Avatar
    01-22-2018, 04:57 PM
    haha...always a work in progress, but remember, I'm coming from a loading cabinet, so It's actually more room in the closet.
    136 replies | 4714 view(s)
  • Kenstone's Avatar
    01-22-2018, 01:39 PM
    Thanks for reading my post and commenting on it. Certainly NOT tongue-in-cheek... I've never seen a Pro 1000 listed separately without dies/powder-measure/shell-plate at Titan....
    136 replies | 4714 view(s)
  • Kenstone's Avatar
    01-21-2018, 11:30 PM
    The Lee Pro 1000s are sold/marketed/setup for one caliber, come with everything needed to load that caliber, and even has a case feeder :wink: You don't even need a scale when using the included Auto Disc powder measure, but it is recommended for...
    136 replies | 4714 view(s)
  • Kenstone's Avatar
    01-21-2018, 01:30 PM
    I buy 38/357 coated bullets...resize them for 9mm/380 keeps the inventory down, :mrgreen:
    71 replies | 2432 view(s)
No More Results
About Kenstone

Basic Information

About Kenstone
Location:
Boysee

Statistics


Total Posts
Total Posts
131
Posts Per Day
0.28
General Information
Last Activity
Yesterday 11:29 PM
Join Date
11-06-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check