Inline FabricationMidSouth Shooters SupplyRotoMetals2Graf & Sons
ADvertise hereStainLess Steel MediaLee PrecisionTitan Reloading

Tab Content
  • Moleman-'s Avatar
    07-19-2018, 02:16 PM
    It's sounding like the 1894 44mag barrel then replace the forearm and hardware if needed is going to be the easiest way to go.
    17 replies | 297 view(s)
  • Moleman-'s Avatar
    07-17-2018, 12:27 PM
    Moleman- replied to a thread Framing gun in Our Town
    I bought a $80 refurbished stanley bostitch and use the whole head nails. Mine didn't look used as it had never had a fitting ever screwed in or any wear marks on the ram or safety guide. Figured it was a closed store buyout or basically they...
    23 replies | 526 view(s)
  • Moleman-'s Avatar
    07-15-2018, 12:29 PM
    Moleman- replied to a thread Coffee in Our Town
    Generally have half of a 12 cup pot at some point during the day. I can fill up my coffee cup almost twice from half a pot.... so I only have 2 or maybe 4 cups of coffee a day.
    56 replies | 1111 view(s)
  • Moleman-'s Avatar
    07-06-2018, 09:36 PM
    I degrease before abrasive blasting anything that goes in the cabinet. That's not always possible and you're right if contamination is an issue boiling with TSP will help. If the parts are greasy you run the risk of peening grease into pockets...
    103 replies | 4825 view(s)
  • Moleman-'s Avatar
    07-06-2018, 07:26 AM
    I used water to make sure any gas was out. There was also an oil sludge at the bottom that stunk of the smell they put in propane and NG to make it detectable.
    22 replies | 694 view(s)
  • Moleman-'s Avatar
    07-05-2018, 12:17 PM
    Good Job! I prefer manganese over zinc parkerizing so unless I'm doing a U.S.A. WWII gun it gets manganese. Tried several brands, even got manganese from a pottery place and made my own. Best/most economical one is Palmetto brand. Been using it...
    103 replies | 4825 view(s)
  • Moleman-'s Avatar
    06-30-2018, 07:56 PM
    Moleman- replied to a thread Ruger 77/50 barrel in Muzzleloading.
    Have you tried calling McGowen? They make ML barrels for the Savage MLII guns, perhaps they also will make one for the Ruger. Might end up pretty close to a used ML in cost though.
    9 replies | 280 view(s)
  • Moleman-'s Avatar
    06-25-2018, 07:51 AM
    The flood coolant is nice on things like barrels where you're taking a long cut as you don't have to keep brushing chips or applying the cutting oil. As bangerjim said I usually do not use the flood coolant for perhaps 95% of the work that gets done...
    51 replies | 1747 view(s)
  • Moleman-'s Avatar
    06-24-2018, 04:32 PM
    Yes, If you try any milling with a drill press if you're lucky the MT2 or Jacobs chuck taper will let go before wrecking the bearings or bending the spindle. Drill presses aren't designed for side loads.
    51 replies | 1747 view(s)
  • Moleman-'s Avatar
    06-24-2018, 04:02 PM
    Similar story for me. Had shop class in high school and got to use lathes and mills, then basically nothing for 20 years when back issues started and I got a 9x20 lathe. 4 surgeries so far and counting and 10 years later I've got lots of spare...
    51 replies | 1747 view(s)
No More Results
About Moleman-

Basic Information

About Moleman-
Location:
SW Michigan next to a winter wheat field

Statistics


Total Posts
Total Posts
500
Posts Per Day
0.69
General Information
Last Activity
Today 11:47 AM
Join Date
07-24-2016
Referrals
0

1 Friend

  1. vzerone vzerone is offline

    Banned

    vzerone
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check