RepackboxReloading UKInline FabricationRotoMetals2
Lee PrecisionMidSouth Shooters SupplyTitan ReloadingADvertise here

Tab Content
  • Moleman-'s Avatar
    Yesterday, 09:22 PM
    Can you use a small dremel diamond ball bit to remove enough metal from the ball so that it will come out? I updated my old projector press to use the LNL subplate and priming system. The subplate kit came with two new bevel head screws which...
    37 replies | 766 view(s)
  • Moleman-'s Avatar
    02-23-2021, 12:47 PM
    Thompson center black powder measure model number 7047. The funnel top slides to strike off the powder charge as opposed to pivots like most of the ones you normally see do.
    13 replies | 569 view(s)
  • Moleman-'s Avatar
    02-20-2021, 11:24 AM
    I wonder if whoever bent the bolt put a 93-96 low swing safety in it.
    10 replies | 363 view(s)
  • Moleman-'s Avatar
    02-18-2021, 05:21 PM
    Parts 5-7 are the safety detent parts and are in the safety lever. Liberty tree has the firing pins for $39
    10 replies | 363 view(s)
  • Moleman-'s Avatar
    02-14-2021, 07:58 PM
    I try for 1.25" on the deepest section, and.650" on the shelf. I have some commercial lowers that are almost .010" deeper.
    5 replies | 334 view(s)
  • Moleman-'s Avatar
    02-03-2021, 03:10 PM
    I remember that ad campaign. At their advice not to use their bullets with the FCD I stopped using them for the most part. Started using more Hornady and Sierra bullets after that as it was a deceptive ad in my opinion.
    26 replies | 1038 view(s)
  • Moleman-'s Avatar
    02-01-2021, 01:35 PM
    Pics did work but wouldn't accept a post.... Now no pics. The bolt looks a lot like a 1871 or 1884 mauser bolt missing the bolt head and extractor.
    7 replies | 398 view(s)
  • Moleman-'s Avatar
    01-29-2021, 09:39 PM
    Moleman- replied to a thread LnL Ram Twist in Reloading Equipment
    I made a new driveshaft out of 1/2" shaft that has a key on the top so it is now set up for the LNL drive hub. Made a collar with a set screw to go on the driveshaft so that a spring pushes the drive shaft and more importantly the index wheel up...
    6 replies | 209 view(s)
  • Moleman-'s Avatar
    01-29-2021, 08:35 PM
    Moleman- replied to a thread LnL Ram Twist in Reloading Equipment
    Neat, thanks for the part numbers.
    6 replies | 209 view(s)
  • Moleman-'s Avatar
    01-29-2021, 06:19 PM
    Here's a couple pics of a couple straight walled sizer dies I made that will work as taper crimp dies with the decapping stem removed. L-R Left- .375FUW die without the decapping stem installed. Middle- test sizer/taper crimp for 400FUW, right-...
    13 replies | 541 view(s)
  • Moleman-'s Avatar
    01-29-2021, 01:36 PM
    Years ago I removed the clip guide on mine to mount a scope. To make it easier to put on/remove take a little off the bottom of the dovetail on the guide (not the receiver). Doesn't take much.
    16 replies | 607 view(s)
  • Moleman-'s Avatar
    01-28-2021, 08:28 PM
    I have made taper crimp dies and prefer lyman style as it is a true slow taper crimp and not an abrupt taper like Lee which tries to form a modified roll crimp. Lee isn't lying that it's a taper, but they're also not telling you they act like a...
    13 replies | 541 view(s)
No More Results
About Moleman-

Basic Information

About Moleman-
Location:
SW Michigan next to a corn field

Statistics


Total Posts
Total Posts
946
Posts Per Day
0.56
General Information
Last Activity
Today 11:02 AM
Current Activity
Viewing Attachment
Join Date
07-24-2016
Referrals
0

1 Friend

  1. vzerone vzerone is offline

    Banned

    vzerone
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check