RotoMetals2WidenersRepackboxMidSouth Shooters Supply
ADvertise hereTitan ReloadingLee PrecisionInline Fabrication

Donate Now Goal amount for this year: 6000 USD, Received: 5750 USD (96%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • Moleman-'s Avatar
    08-18-2019, 03:33 PM
    Got a drill press? Before getting a lathe I fixed the straight ones by drilling a shaft sized hole halfway though a 3/4"-1" section of steel (aluminum will work in a pinch) and without removing the piece from the vise, switch over to a smaller pin...
    3 replies | 168 view(s)
  • Moleman-'s Avatar
    08-18-2019, 11:54 AM
    Been doing similar for years only with red loctite. They don't seem to last as long as the original "needle bearing" type pins, but do last longer than the current soft one piece pins that have been with the past few die sets I've bought.
    3 replies | 168 view(s)
  • Moleman-'s Avatar
    08-17-2019, 08:45 PM
    Moleman- replied to a thread USGI sea stories in Our Town
    My buddy lost an M16 while on guard duty in port on his sub. Said the sling broke and the rifle was falling before he knew what was happening. He said he could still hear the sound of the rifle hitting the hull and splashing into the water. Of...
    97 replies | 4400 view(s)
  • Moleman-'s Avatar
    08-16-2019, 10:11 AM
    I think it involved a cold snap, something about ICE.
    41 replies | 1348 view(s)
  • Moleman-'s Avatar
    08-13-2019, 02:14 PM
    If he has had the gas block off for some reason there is a good chance that he is correct. Misaligned gas block is a common issue along with leakage at the block, gas key and rings. If he takes off the gas block you can center the rear screw hole...
    4 replies | 93 view(s)
  • Moleman-'s Avatar
    07-29-2019, 11:49 AM
    If the measurement needs to be better than +- .001" I use a micrometer.
    52 replies | 1356 view(s)
  • Moleman-'s Avatar
    07-27-2019, 02:27 AM
    Rebarreled mine in 44x1.8" with an octagon barrel for use in our "limited firearms deer zone" a few years back.
    21 replies | 1579 view(s)
  • Moleman-'s Avatar
    07-26-2019, 01:09 PM
    Moleman- replied to a thread Is my mold worn out? in Cast Boolits
    I have the same pot. Aim the stream of lead into the sprue hole and when it's full move to the next one without stopping the flow of lead. ideally when you break off the sprue it's a string that stays together.
    40 replies | 1132 view(s)
  • Moleman-'s Avatar
    07-26-2019, 11:28 AM
    Moleman- replied to a thread Is my mold worn out? in Cast Boolits
    I have several Lee 6-cavity molds and several NOE 4- cavity molds. They all have to be run hotter than any of my 2 cavity molds. I set them on top of the Lee pot as it is coming up to temp and then dip the bottom of one end into the lead until it...
    40 replies | 1132 view(s)
  • Moleman-'s Avatar
    07-25-2019, 08:07 AM
    I wouldn't consider the 90's manufacture remotely as "old" powder if it was stored halfway decent.
    17 replies | 1144 view(s)
No More Results
About Moleman-

Basic Information

About Moleman-
Location:
SW Michigan next to a corn field

Signature


350 Legend, imitation is the highest form of flattery. Aww, Thanks Winchester!

Statistics


Total Posts
Total Posts
750
Posts Per Day
0.67
General Information
Last Activity
Yesterday 10:14 PM
Join Date
07-24-2016
Referrals
0

1 Friend

  1. vzerone vzerone is offline

    Banned

    vzerone
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check