Graf & SonsTitan ReloadingStainLess Steel MediaRotoMetals2
Lee PrecisionWidenersMidSouth Shooters SupplyInline Fabrication

Tab Content
  • Moleman-'s Avatar
    09-14-2018, 07:28 PM
    Should be able to get under the 8# mark with an optic without too much effort. This 44x1.8" wildcat came in at 8#3 oz with the scope and magazine but without the suppressor. It has a fairly heavy barrel profile at .980" to the .875" gas block,...
    29 replies | 2085 view(s)
  • Moleman-'s Avatar
    09-12-2018, 07:16 PM
    There is a copy of the 870 that is made in china since the design is no longer under patent protection, but the last 870 I bought last fall was made in the USA. The chinese copies are sold under different names and not by Remington, hawk 982 is one.
    76 replies | 1394 view(s)
  • Moleman-'s Avatar
    09-12-2018, 06:07 PM
    I'd just measured the expander stems I'd made to fit in a Lee powder through die yesterday because someone on another site had asked what thread they were (5/8"-24TPI). I hate to go off of memory and still had the thread gauge and micrometer out. ...
    3 replies | 162 view(s)
  • Moleman-'s Avatar
    09-12-2018, 01:35 PM
    5/8"-18TPI on the ones I have
    3 replies | 162 view(s)
  • Moleman-'s Avatar
    09-11-2018, 09:08 AM
    My best friend likes the 500 and I like the 870. His is old enough that it has a metal safety, but still has the plastic trigger housing. Another highschool buddy (a lefty) has had both and went from the 500 to 870's and has stuck with Benelli...
    76 replies | 1394 view(s)
  • Moleman-'s Avatar
    09-07-2018, 12:07 PM
    The hydrid is available with a qd back plate that uses their muzzle brakes. I prefer to use it as it doesn't matter what the barrel thread diameter or pitch is if you want to swap it between guns. the downside is that you will need to put a $75...
    18 replies | 456 view(s)
  • Moleman-'s Avatar
    09-06-2018, 06:27 PM
    I tried this with a modified 223 case and couldn't get them to shoot very well. Just went back to the pellet gun or 12ga if they're too far away. Of course we don't have any houses by us though.
    12 replies | 490 view(s)
  • Moleman-'s Avatar
    08-29-2018, 08:58 PM
    Moleman- replied to a thread cop here lost his car in Our Town
    They make lockouts so you can keep the engine running for the electronics (and AC) with the key removed. They kill the engine if you try to put them in gear. The chief may want to rethink the cost of putting them in.
    20 replies | 1061 view(s)
  • Moleman-'s Avatar
    08-29-2018, 06:35 PM
    I've got a few uppers that I use with lee tumble lube bullets with alox and then dusted with mica which can really clog things up with lube. The bolt carrier group especially gets dirty when you put a few hundred cast loads through it. While you're...
    26 replies | 986 view(s)
  • Moleman-'s Avatar
    08-29-2018, 08:26 AM
    Any die set that will reload the 357Max will load these. I don't like having to modify die sets if I can help it. The best crimping die that I've found is the 38/357 Lyman taper crimp die as it is actually a gentle taper v/s a modified roll crimp...
    37 replies | 6085 view(s)
  • Moleman-'s Avatar
    08-27-2018, 07:48 AM
    Read through this thread on a 45-70 using a round block. I got a block of 4140 prehardened to make one at some point hopefully after deer season.
    20 replies | 588 view(s)
  • Moleman-'s Avatar
    08-19-2018, 06:03 PM
    Step brother and his family had one. It would chew anything when bored and was not good with strangers as it it liked to nip at them if they tried to pet it until the day it died. They were not first time dog owners and had a difficult time...
    16 replies | 657 view(s)
No More Results
About Moleman-

Basic Information

About Moleman-
SW Michigan next to a winter wheat field


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 01:39 PM
Join Date

1 Friend

  1. vzerone vzerone is offline


Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check