WidenersInline FabricationStainLess Steel MediaTitan Reloading
RepackboxMidSouth Shooters SupplyRotoMetals2Graf & Sons
Lee Precision
  • M-Tecs's Avatar
    Today, 03:19 AM
    M-Tecs replied to a thread 6.5 Creedmore - NOT in Factory Rifles
    Yes it will feed the very long bullets used by the long range competitors out of a 308 length mag. With the .260 using the same long bullets the mag runs out of space.
    68 replies | 3247 view(s)
  • M-Tecs's Avatar
    10-09-2018, 11:52 AM
    Sometimes they fit but normally they require fitting . http://www.ktgunsmith.com/45acp_cyl.htm
    15 replies | 671 view(s)
  • M-Tecs's Avatar
    10-09-2018, 11:49 AM
    In the early 1900's it was very common for competition shooting. It greatly reduces fouling. Most BP competitions do not allow it today. http://castboolits.gunloads.com/showthread.php?137201-Black-powder-duplex-loads
    21 replies | 690 view(s)
  • M-Tecs's Avatar
    10-04-2018, 06:21 PM
    I will take the Lyman 4 Cavity Mold 357446 .358" 162gr SWC with nutcracker handles $65 Shipped USPS Priority mail medium flat rate box using PayPal. PM sent
    18 replies | 2120 view(s)
  • M-Tecs's Avatar
    09-29-2018, 11:47 PM
    No disagreement. I love the.17 Mach 2. My favorite is a Magnum Research semi-auto with a Kidd two stage trigger, I also have the .17 Mach 2 in CZ's, Sako Quads and Contenders. That doesn't change the fact that the cartridge is almost dead. ...
    11 replies | 349 view(s)
  • M-Tecs's Avatar
    09-29-2018, 12:44 PM
    That is one of the primary reasons the cartridge is on life support. Dirty chambers in a shouldered rimfire in semi-auto don't mix so chamber dimension's between manufactures vary greatly. Between the case splits and slam fires ammo manufactures...
    11 replies | 349 view(s)
  • M-Tecs's Avatar
    09-29-2018, 04:59 AM
    Shot some prairie dogs and a couple of skunks with mine. It has been very effective on them.
    11 replies | 349 view(s)
  • M-Tecs's Avatar
    09-28-2018, 09:25 PM
    Like most long range rifle competitors I mostly load on a progressive. We all have no problem holding 1/2 MOA out to a 1,000 yards with a progressive. To produce extremely accurate ammo the same steps have to be followed. Press type makes very...
    61 replies | 1699 view(s)
  • M-Tecs's Avatar
    09-26-2018, 09:11 PM
    Started reloading in at 9 or 10 years old for a re-enactment club. Loading about 50,000 rounds for them on a single station press. Reloading was never fun until I purchased a 1050.
    61 replies | 1699 view(s)
  • M-Tecs's Avatar
    09-21-2018, 10:50 PM
    I have the same question. In the .556 I don't recommend a carbine length gas system. On my match rifles I extend the rifle length gas system 2". I have zero experience with the 458 SOCOM but everything I have read states the carbine length gas...
    10 replies | 368 view(s)
  • M-Tecs's Avatar
    09-21-2018, 09:11 PM
    That would be my point. Consumers rejected lower velocity of the 17 HM2. A low velocity 17 HMR load would fair no better.
    35 replies | 1287 view(s)
  • M-Tecs's Avatar
    09-19-2018, 11:29 PM
    They do it's called the 17 Mach 2 but it didn't sell well and the gun manufactures made the chambers too loose in the semi-auto's so neck and case splits are fairly common. I have several and really like them but I purchased 8K of ammo at a...
    35 replies | 1287 view(s)
  • M-Tecs's Avatar
    09-18-2018, 12:44 AM
    https://www.americanrifleman.org/articles/2018/9/17/former-ruger-ceo-william-b-ruger-jr-passes-away/ Sturm, Ruger & Co. is mourning the death of William B. Ruger Jr., former chairman of the board and chief executive officer of Ruger. The...
    2 replies | 125 view(s)
  • M-Tecs's Avatar
    09-15-2018, 08:56 PM
    That could be possible.
    53 replies | 1704 view(s)
  • M-Tecs's Avatar
    09-15-2018, 02:25 PM
    Awhile back I was doing a lot of selling and trading at gun shows. Later I was looking for something else I a discovered a S&W 629 that I have no idea when or how I came to own it.
    53 replies | 1704 view(s)
  • M-Tecs's Avatar
    09-14-2018, 10:22 PM
    M-Tecs replied to a thread Are you "particular"? in Cast Boolits
    It depends on the intended usage of the ammo and guns. For my cowboy action it being safe and reliable is the only real requirement. On my 1,000 yard match rifles I do what to know and control every deal as precisely as humanly possible. On the...
    58 replies | 1503 view(s)
No More Results
About Tnfalconer

Basic Information

About Tnfalconer
Location:
Great falls Montana

Statistics


Total Posts
Total Posts
203
Posts Per Day
0.25
General Information
Last Activity
10-08-2017 05:34 PM
Join Date
07-14-2016
Referrals
0

1 Friend

  1. M-Tecs M-Tecs is offline

    Boolit Master

    M-Tecs
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check