Titan ReloadingRotoMetals2StainLess Steel MediaGraf & Sons
RepackboxInline FabricationMidSouth Shooters SupplyLee Precision
Wideners
Tab Content
  • Walks's Avatar
    Today, 04:17 PM
    BLAST IT !!! 8 minutes and not even a dollar short.
    11 replies | 337 view(s)
  • Walks's Avatar
    Today, 03:31 PM
    Walks replied to a thread Sticky Powder in Reloading Equipment
    Well, I've learned through experience that TITEGROUP has to be emptied out of the Measure as soon as you're done with that loading session. I don't even leave it in from 10pm until 8am to start loading again. I empty the Measure, then take it out...
    7 replies | 151 view(s)
  • Walks's Avatar
    Today, 03:17 PM
    Walks replied to a thread West Coast deer hunting in Leverguns
    That's GREAT, I grew up in SoCal, can't hunt anymore. But in my day I hunted from from San Diego Cnty up to Fort ORD. AND that is a Fine Buck for the Coast. Congratulations. Hope you took good care of the meat.
    4 replies | 127 view(s)
  • Walks's Avatar
    Today, 01:09 AM
    I've been reloading for almost 60yrs. Had one stuck bottleneck rifle case. Using RCBS Case Lube-2 on a lube pad. Was teaching a newbie about reloading. Laid 5 clean .25-06 cases on top of a Lube pad. FORGOT to roll the cases across the pad....
    61 replies | 47389 view(s)
  • Walks's Avatar
    Today, 12:06 AM
    Anybody every empty their powder measure & have the powder stick to the side of the hopper ?
    7 replies | 151 view(s)
  • Walks's Avatar
    Yesterday, 04:09 PM
    roysha, The measure is not throwing random charges. The brass shavings that are dislodged from the Expander die are already in the case when it goes up into the Powder Measure. The difference in thrown charges are a result of random amounts...
    7 replies | 332 view(s)
  • Walks's Avatar
    Yesterday, 03:53 PM
    Coleman & beagle are right on Point. I used a pure lead #429244HP with out gas check in a T/C HAWKEN .50cal The GOULD Bullet sounds like a good idea for .54 cal, might try it.
    18 replies | 243 view(s)
  • Walks's Avatar
    Yesterday, 03:40 PM
    Walks replied to a thread Would you accept this?! in Cast Boolits
    I would call back and complain, if they wouldn't swap out a new correctly made gun, that worked right, straight out of the box. I would send a LETTER & PICTURE to every gun mag & every website out there. The squeaky wheel gets the grease.
    40 replies | 1414 view(s)
  • Walks's Avatar
    10-17-2018, 11:20 PM
    Yep, but it doesn't take much at 5.5grs of powder, to go to 5.9grs.
    7 replies | 332 view(s)
  • Walks's Avatar
    10-17-2018, 11:11 PM
    I've had that LEE WC mold for 30+yrs. Cast of 20/1 over 6.0grs of UNIQUE, makes a light, accurate & pleasant load. Every time I see one on flea-bay, I always get out bid.
    31 replies | 714 view(s)
  • Walks's Avatar
    10-17-2018, 11:02 PM
    I use .32 WS brass for my .30WCF Cast Bullet Loads.
    15 replies | 991 view(s)
  • Walks's Avatar
    10-17-2018, 05:21 PM
    I've been loading .44MAG for COWBOY ACTION SHOOTING for my Chiropractor for 15+yrs. The load he favors is a 240gr RNFP over 5.5grs of TITEGROUP. The Patient who started him in CAS, loaded this load for him before I took over after that...
    31 replies | 714 view(s)
  • Walks's Avatar
    10-17-2018, 03:23 AM
    Discovered what it was tonight. Tiny brass shavings from a DULL chamfer/deburr tool left were being dislodged into some of the cases by the expander die, before going up into the powder measure. Used a new chamfer/deburr tool on 50 cases,...
    7 replies | 332 view(s)
  • Walks's Avatar
    10-17-2018, 03:09 AM
    tomme boy has it right. Most people slam any kind of brass thru a PROGRESSIVE. All they do is clean and barely sort to get rid of the stray 380. I keep my brass in lots/boxes of 50 or 100. Sorted by headstamp, never mixed. Checked for length. I...
    63 replies | 1668 view(s)
  • Walks's Avatar
    10-15-2018, 03:04 PM
    Walks replied to a thread What are these, Orbs? in Our Town
    It's either the evil SPIRIT of your mother-in-law's ghost. Or swamp gas. Or if she's still with us, just her evil SPIRIT hanging around. Or swamp gas. Then again it could be somebody taking AMBIEN, out for a stroll with a flashlight. ...
    43 replies | 1255 view(s)
  • Walks's Avatar
    10-15-2018, 02:48 PM
    Walks replied to a thread mountain lion in NH in Our Town
    Here in the City of Los Angeles, The Black Bears go swimming in people's pools. Mountain Lions, they eat the trail bikers & hikers. Had one cruising the Santa Monica 3rd Street Mall a few years back. Coyote's will come in a doggy door and...
    41 replies | 1022 view(s)
  • Walks's Avatar
    10-15-2018, 02:23 PM
    Walks replied to a thread Wal-Mart screw up in Rimfire Area
    Well, Took those REM "Golden Bullets" out 2 Saturday's ago. They shot in 3 different RUGER 10/22's, 2 MARLIN 60's, 2 NYLON 66's, MARLIN 39D, REMINGTON 552 & 572, WINCHESTER 62A, couple of those cheap ROSSI pumps and at least 3 bolt guns I don't...
    57 replies | 3288 view(s)
  • Walks's Avatar
    10-15-2018, 01:14 PM
    Early 1892's had small bore's. IDEAL/LYMAN used to make a #42498 mold. My DAD had one. It was a bit of a pain casting/sizing/loading bullets from a single cavity mold. Just for that one carbine. Had to pan lube and size in a LYMAN 310 Die. My...
    10 replies | 321 view(s)
  • Walks's Avatar
    10-14-2018, 11:18 PM
    Groo, Same reason COLT didn't do it in the SAA.
    20 replies | 707 view(s)
  • Walks's Avatar
    10-14-2018, 10:55 PM
    LYMAN 55 RCBS Little Dandy HORNADY, an old one. RCBS Duo-Measure RCBS Uniflow HORNADY L-N-L LEE Dippers BELDING & MULL, old but still works, wish I knew where it was ? Forgot the LYMAN DPS 1200
    295 replies | 66617 view(s)
  • Walks's Avatar
    10-14-2018, 10:29 PM
    I went out to start loading 1000 new Starline .44mag cases today. My Chiropractor needs COWBOY AMMO in 10 days. Got everything I need, Cases are fully preped & primed, Bullets are sized & lubed, Powder aplenty. Changed, shellplate,dies, Powder...
    7 replies | 332 view(s)
  • Walks's Avatar
    10-14-2018, 04:34 PM
    .35 Whelen, had on 30yrs now. REM 700 CLASSIC. Use a light load with the LYMAN #358315/212grs. Heavy load, I use the old #358318 an old mold no longer in Production. Weighs 245-260grs depending on alloy. Both are Gas Checked. I have an old IDEAL...
    21 replies | 475 view(s)
  • Walks's Avatar
    10-14-2018, 03:23 PM
    Walks replied to a thread carrying bullets? in Muzzleloading.
    When I could still hunt, I carried the "Speedloaders" on a Lanyard around my neck, along with my short starter. The Speedloaders I used were the two compartment type with a percussion cap holder in one of the caps. For storing cast & lubed...
    26 replies | 769 view(s)
  • Walks's Avatar
    10-14-2018, 02:12 PM
    I had a buddy, who's stainless pot melted all over his COLEMAN Stove. And it was a quality AMERICAN MADE POT he'd had for 20yrs. CAST IRON IS THE ONLY SAFE VESSEL FOR MELTING LEAD OVER A PROPANE FLAME. Wood stove will take a long time to heat...
    18 replies | 412 view(s)
  • Hamish's Avatar
    10-14-2018, 11:17 AM
    Hamish replied to a thread Stupid Things I Do in Cast Boolits
    Work it up using the load data of the faster of the two powders. Come on kids, let's use a little logic here,,,,,,
    29 replies | 976 view(s)
  • Walks's Avatar
    10-14-2018, 12:35 AM
    Extractor's mostly, sometimes the lifter jammed, or even broke off completely. Sometimes the barrel wouldn't reseat after being removed. Had one that the buttstock split 6 inches from the tang. And more broken off safeties then I could count.
    191 replies | 4819 view(s)
More Activity
About Walks

Basic Information

About Walks
Biography:
Reloading 59yrs, Shooting 59yrs, Casting 55yrs.
Location:
SoCal
Interests:
Reloading,Rifles,Revolvers,casting,reading
Occupation:
Disabled

Signature


Happiness is a Warm GUN & more ammo to shoot in it.

Statistics


Total Posts
Total Posts
546
Posts Per Day
0.64
General Information
Last Activity
Today 11:41 PM
Current Activity
Viewing Attachment
Join Date
06-13-2016
Referrals
0

5 Friends

  1. Calamity Jake Calamity Jake is offline

    Boolit Master

    Calamity Jake
  2. Hamish Hamish is offline

    Boolit Master

    Hamish
  3. Hi-Performance Bullet Coatings
  4. jetsfan-24 jetsfan-24 is offline

    Boolit Man

    jetsfan-24
  5. sniper sniper is offline

    Boolit Buddy

    sniper
Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check