RotoMetals2Titan ReloadingADvertise hereLee Precision
MidSouth Shooters SupplyRepackboxInline Fabrication

Tab Content
  • Drm50's Avatar
    Today, 05:48 PM
    The older Lyman 66 had a small “lip” at top of base that would allow you to precisely locate base holes. I don’t think Williams has this lip, so it can be used on several flat sided levers. The 1894 receivers aren’t hard to drill. The main thing is...
    7 replies | 75 view(s)
  • Drm50's Avatar
    Today, 01:18 PM
    I’ve cut off several 22 rifles which is easiest to get rid of bore damage at muzzle. I have had one case that I was forced to counter bore. With my luck it was my own gun. I had a Savage 24 in 22/410 hid in my cabin. Before deer season I always took...
    12 replies | 243 view(s)
  • Drm50's Avatar
    Today, 11:49 AM
    I took some S&W autos as partial part of sale on a S&W m57 6” NIB / wooden case. Have no interest in them so they are strictly trade bait.
    212 replies | 8500 view(s)
  • Drm50's Avatar
    Today, 11:39 AM
    Drm50 replied to a thread Remington rifles in Factory Rifles
    My best buddy used to make fun of me for buying older used guns for the same money or more that I could buy a new Remington 700. I remember the day we stopped at LGS to pick up a new Rem 700 in 8mm mag. Shop had just taken in a 1895 Win 30/40 cal. I...
    2 replies | 214 view(s)
  • Drm50's Avatar
    Today, 09:07 AM
    Bump to top
    1 replies | 321 view(s)
  • Drm50's Avatar
    Yesterday, 06:09 PM
    Drm50 started a thread WTS sights in Swappin & Sellin
    Left to right/ top to bottom (1) Lyman 66R receiver sight, old model all steel in mint shape. Fits 742/ 760 Rems also 14/141 Rem. This sight is missing range plate and screw which can be had for about $15 with shipping. As is .........$75 (2)...
    1 replies | 288 view(s)
  • Drm50's Avatar
    Yesterday, 04:41 PM
    I guess what I was talking about is a super super 357 max. Proportioned like 44mg is to 444. I say 357 because its smallest legal diameter. Most hunting accidents in Ohio take place at starting or finishing point. More are hurt and killed...
    29 replies | 666 view(s)
  • Drm50's Avatar
    Yesterday, 04:28 PM
    Drm50 replied to a thread Matching your revolver in Leverguns
    I have a couple Marlin Levers, a 1897 and a 39m and 6 22 revolvers / 5 22 auto pistols. These are probably the most useful to shoot with one ammo. I’ve got a Marlin 1894 44mg and Ruger SBH and two m29-2 S&Ws. Can’t see carrying both unless under...
    18 replies | 324 view(s)
  • Drm50's Avatar
    Yesterday, 12:09 PM
    Drm50 replied to a thread whats the deal in Our Town
    I’m in good shape on guns, ammo, loading tools and components. I didn’t realize panic and shortage was in everything. Building material and any consumer goods that has anything to do with panic and preppers. Last month won 1/2 a beef from local 4H....
    19 replies | 426 view(s)
  • Drm50's Avatar
    Yesterday, 11:52 AM
    I have owned and or shot tons of 32 cal pistols and revolvers. From break top 32short to 327mag in revolvers and 7.63mm in pistols. Never experience any that I would rate as uncomfortable to shoot because of recoil.
    665 replies | 310965 view(s)
  • Drm50's Avatar
    Yesterday, 11:33 AM
    I have a Marlin 1894 octagon barrel rifle and a Win 53 in 25/20. Being into 25/20 & 32/20 for 50yrs they are hard to find with nice bores. Both mine shoot excellent with cast bullets. The Marlin bore is dark but not pitted or rusted. The 53 is one...
    18 replies | 292 view(s)
  • Drm50's Avatar
    09-27-2020, 07:19 PM
    375Win is hot 38/55. Case is heavier but little shorter. The point I was trying to make is the straight cases are like a arms race. The whole idea of them was to limit velocity/ range. The traditional deer rifles 30/30, 32, 35Rem are no more...
    29 replies | 666 view(s)
  • Drm50's Avatar
    09-27-2020, 04:48 PM
    High Standard HD-Military 22 pistol. Gun has blue wear and minor dings from use. This is 63/4 barrel. Price $550 Ship to your FFL on your dime. Trades considered
    1 replies | 321 view(s)
  • Drm50's Avatar
    09-27-2020, 01:57 PM
    White Tail deer are not Cape Buffalo. In Ohio we must use 38cal minimum. Most deer shoot under 100yds. A 357mg is adequate for the job. Obsessing over meta plates and hollow points is arm chair stuff. I have 45/70, 44mg and 375Win. The 45/70 is a...
    29 replies | 666 view(s)
  • Drm50's Avatar
    09-26-2020, 10:08 AM
    Left to Right- Top to Bottom: (1) K frame magnas, black washer, diamond, square butt/ flat bottom.............$100 (2) N frame magnas, black washer, square butt/ flat bottom...........................$100 (3) K frame, after market, smooth finger...
    1 replies | 260 view(s)
  • Drm50's Avatar
    09-26-2020, 09:35 AM
    I’m in process of selling off my guns. I just sold my 513, my last remaining BA Rem 22. I still have a Rolling Block with a 513 barrel. I’ve got target sights on it. This was my official Turkey Shoot Gun for years. Shoots were 100ft. I enjoyed...
    35 replies | 648 view(s)
  • Drm50's Avatar
    09-25-2020, 10:51 PM
    Drm50 replied to a thread What's your favorite in Leverguns
    Winchester, Marlin & Savage. All three brands I have cut off dates that I have no interest in guns made after that date. Don’t do Henry or Rossi at all, nor new production Marlins from Rem or new Win repro from Japan.
    21 replies | 312 view(s)
  • Drm50's Avatar
    09-25-2020, 08:27 AM
    I have small Fishing Tackle box that is official target box. Stapler, roofing nails, celotex nails, hammer and tape for hanging targets. Also have pliers, wire, cable ties and Duct tape. We usually take battery drill and selection of drywall screws...
    22 replies | 498 view(s)
  • Drm50's Avatar
    09-24-2020, 06:55 PM
    I been using Speer 130gr HP in 300Sav for years/ IMR-4895. Before I used a Rem 170gr RN, same one Rem used in factory loads. The discontinued it’s sale years ago. I have no 99 in 300sav only a Rem 81.
    33 replies | 474 view(s)
  • Drm50's Avatar
    09-24-2020, 11:41 AM
    If making mags was simple there would be a lot of them on the market. Many of the aftermarket mags at $40 @ don’t work that well. I’ve got 22 mags I have no idea what they are for. At $5 I never let one get buy. Voere, I would have to see one to...
    34 replies | 714 view(s)
  • Drm50's Avatar
    09-23-2020, 10:14 PM
    Drm50 replied to a thread Remington Mod 37 mags in Rimfire Area
    I have never owned a 37, I too am Bogarting a mag for the one that will come down the road. I’ve had a dozen Win 52s, I think there must have been a lot more of them than Rem 37s.
    3 replies | 93 view(s)
  • Drm50's Avatar
    09-18-2020, 02:58 PM
    Got a Colt NS that I use 45AR cases with rims thinned. Gun is excellent and didn’t want to CS cylinder. My bullet is from modified Lyman Ideal, 322gr Gould Express HP. Boolit is 272gr hp. I settled on 4.5grs of Unique. I still have original notes, I...
    23 replies | 348 view(s)
  • Drm50's Avatar
    09-18-2020, 10:37 AM
    Bump to top
    3 replies | 390 view(s)
  • Drm50's Avatar
    09-17-2020, 11:23 PM
    Drm50 replied to a thread Ruger M77 .220 Swift in Factory Rifles
    I had 77v in 220 Swift. I shoot 55gr in all my CF 22s except Hornet. Ruger would shoot 1” at 100yds. I had a Redfield 16x. 220 was my favorite only one I have left is a custom 98 varmit.
    12 replies | 371 view(s)
  • Drm50's Avatar
    09-17-2020, 11:50 AM
    I did a scope once, didn’t work out well. In Jack O’Connor’s book the chapter on scopes has in 1st paragraph, Two kids of people take scopes apart, experts and fools. I was not in expert category. Getting the older scopes serviced is pricey.
    6 replies | 171 view(s)
  • Drm50's Avatar
    09-17-2020, 11:05 AM
    I had a highly sporterized carbine a few years back. Fancy stock, Blue and scope. Unfortunately as neat looking as it was, it didn’t shoot that well. I tried several bullets and the Sierra 110 was feed problem. The Speer 110 HP was not , nor the RN...
    10 replies | 296 view(s)
  • Drm50's Avatar
    09-16-2020, 08:44 AM
    Bump to top
    3 replies | 390 view(s)
  • Drm50's Avatar
    09-15-2020, 08:46 AM
    I have a big old South Bend, belt drive but I was interested in one of those small $500-700 jobs. Buddy of mine bought one and it’s a joke for anything serious. Might be ok for crafts if you are turning soft materials. In my neck of the woods it’s...
    63 replies | 1737 view(s)
  • Drm50's Avatar
    09-14-2020, 03:27 PM
    I have several Arrow T-50s and a Craftsman that works backwards. It can also drive small brads. I have a couple smaller Arrows that will work fine for just target to backing. I only want to carry one so a T50 is in target box.
    22 replies | 498 view(s)
  • Drm50's Avatar
    09-14-2020, 03:16 PM
    I’ve found S&Ws to be extremely accurate with cast boolits sized for the particular gun. I have and have had many, many S&Ws. I had no interest in service revolvers of Colt or S&W. I had several Pythons in 60 & 70s. Very fine shooting and I never...
    31 replies | 915 view(s)
More Activity
About Drm50

Basic Information

About Drm50
Biography:
Army vet..ex coal miner
Shooting & fishing before I could walk
Location:
SE Ohio
Interests:
Hunting,Fishing, Gun Collecting
Occupation:
Contractor

Statistics


Total Posts
Total Posts
1,995
Posts Per Day
1.27
General Information
Last Activity
Today 05:56 PM
Join Date
06-08-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check