ADvertise hereInline FabricationLee PrecisionRepackbox
Titan ReloadingWidenersRotoMetals2

Tab Content
  • Drm50's Avatar
    01-22-2020, 01:27 PM
    There is to much over thinking on cartridges and bullets for deer. A 30/06 is plenty of gun for deer and the best bullet is the one your rifle shoots best. All the Hunter has to do is make a decent shot. Gimmick bullets don't make up for poor shots.
    52 replies | 2232 view(s)
  • Drm50's Avatar
    01-18-2020, 04:53 PM
    I’ve got a few 357s and they shoot very well. I have m19s & m27 S&Ws. They are ok but when you get right down to it if you are shooting a lot of 38Spec loads you don’t need a 357mg. I say 357 is minimum and marginal for deer size game and only at...
    72 replies | 2835 view(s)
  • Drm50's Avatar
    01-17-2020, 06:12 AM
    I have Brownell's screw drivers and several other top shelf sets. I have been thinking of buying bit type set. I use drill/ drivers almost every day and can tell you their is a big difference in quality of bits. Brand name means nothing because most...
    28 replies | 782 view(s)
  • Drm50's Avatar
    01-14-2020, 09:46 PM
    There are several Savage/Stevens 94 series shotguns as well as many store brands they were sold under. Most of early guns 94 thru 94c, the barrels will fit the actions. The PIA is the forend latch type. The forend stud on barrel aren’t the same. I...
    8 replies | 384 view(s)
  • Drm50's Avatar
    01-14-2020, 09:29 PM
    The only major leading I’ve ever had was with factory swaged lead bullets. I cast for several calibers and size for individual rifles. I use to cast hard bullets but I don’t anymore. I shot loads of cast in revolvers and original LV type rifles at...
    27 replies | 1166 view(s)
  • Drm50's Avatar
    01-14-2020, 11:58 AM
    I didn’t have any interest in service type revolvers when I first got heavy into guns in early 60s. S&W and Colts were a dime a dozen used. When I started shooting m10s I found that if you shot 158gr police loads they were on the money.
    36 replies | 2843 view(s)
  • Drm50's Avatar
    01-09-2020, 06:49 PM
    Drm50 replied to a thread Winchester M95 Russian in Leverguns
    I used 200gr RN cast for 30/40 Krag. I got my loads out of a Lyman manual from 40s. The 1895 Win action is best kept under 4500psi I had several original 1895s. 30/40, 30govt06, 7.62 Rus and 303 Brit. They all did better with RN bullets, cast or...
    12 replies | 795 view(s)
  • Drm50's Avatar
    01-08-2020, 08:24 AM
    Having to use straight case cartridges have done a lot with them last 5yrs. Mostly with 45/70, 375W and 44mg. 45/70 Marlin 1895 JM and #3 Ruger. 300gr JHPs. Used IMR-3031 & 4198. The Marlin edged the #3 by a hair at 100yds. The 375Win in Marlin and...
    26 replies | 1351 view(s)
  • Drm50's Avatar
    01-08-2020, 07:59 AM
    Drm50 replied to a thread 223 load with BLC2 in Factory Rifles
    I have used BL-C2 as my standard load in Rem 722 in 222 with 55gr bullets for years. I don’t do ARs but I have a #3 Ruger 223 that I load 26.5gr of BL-C2 / 55gr Hornady SX at 3100fps.
    26 replies | 1267 view(s)
  • Drm50's Avatar
    01-07-2020, 11:58 AM
    I would have bought that deal even if I had no use for it. Does Canada have restrictions on barrel length now that they didn’t have before? It’s been 10yrs since I’ve hunted bear in Canada. I use to go 2-3 times a year and always took two rifles. My...
    24 replies | 1075 view(s)
  • Drm50's Avatar
    12-30-2019, 08:24 PM
    Williams made Jumbo Head Left hand safety for 870-1100s. I still see a lot of them around sales.
    13 replies | 402 view(s)
  • Drm50's Avatar
    12-29-2019, 09:29 PM
    Their are things you can put on leather and it will wipe out mildew and mold. It will also rot the leather. I have some Elpaso Saddelry holsters 40 yrs old that have never hade mold or mildew on them. I have news low end holsters that mill dewed in...
    33 replies | 1577 view(s)
No More Results
About Drm50

Basic Information

About Drm50
Biography:
Army vet..ex coal miner
Shooting & fishing before I could walk
Location:
SE Ohio
Interests:
Hunting,Fishing, Gun Collecting
Occupation:
Contractor

Statistics


Total Posts
Total Posts
1,515
Posts Per Day
1.14
General Information
Last Activity
Yesterday 04:42 PM
Join Date
06-08-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check