MidSouth Shooters SupplyRotoMetals2Inline FabricationADvertise here
Lee PrecisionStainLess Steel MediaGraf & SonsTitan Reloading

  • Jniedbalski's Avatar
    04-13-2018, 10:42 PM
    The chamber is not 45/70. If it was a over pressure round it would shoot ,hard to extract or blow the gun up. The brass flowed out to fit the chamber. You can’t make the chamber that much bigger by shooting a high pressure load. It would shoot...
    11 replies | 394 view(s)
  • Jniedbalski's Avatar
    04-12-2018, 05:49 PM
    Jniedbalski replied to a thread Gas-Oh-Leen in Our Town
    Same here
    33 replies | 729 view(s)
  • Jniedbalski's Avatar
    04-11-2018, 05:35 PM
    Dixie gun works still I thank sell molds like this. They where actually women’s hair curlers. But Dixie just got different cherries and cut them out to make a mold
    6 replies | 226 view(s)
  • Jniedbalski's Avatar
    04-11-2018, 03:25 PM
    Stoning it off will be quick and easy a few minutes of time and it will be fine
    14 replies | 349 view(s)
  • Jniedbalski's Avatar
    04-08-2018, 12:53 AM
    There is nonthing wrong with the lee loder. It’s slow but who cares. It does load good ammo. You can load 50 to 100 rounds just sitting around after supper. With the dipper you are limited to only a few powders listed with the lee directions. This...
    24 replies | 694 view(s)
  • Jniedbalski's Avatar
    04-07-2018, 09:37 PM
    I have some 45 acp large primer brass up for sale. I have had this brass 5 or 6years but no 45.this is from a out door police and civilian range. Most of the brass was very clean and new when I picked it up. I have cleaned it with citric acid and...
    0 replies | 150 view(s)
  • Jniedbalski's Avatar
    04-07-2018, 12:36 AM
    I have for sale a lee 220 swift two die set. It is a collet neck sizing die and a dead length bullet seating die. I havenít used this die in 12 years . No longer have the gun. It comes with the shell holder and powder scoop and the round yellow...
    1 replies | 69 view(s)
  • Jniedbalski's Avatar
    04-06-2018, 08:38 PM
    In se Missouri we have a state ,conservation land and range that is free. The hunting area is over 1200 acres with three stocked fishing ponds. They also have a horse and walking trail, small camping areas.This runs along a big creek boat ramp ...
    54 replies | 1632 view(s)
  • Jniedbalski's Avatar
    04-02-2018, 03:25 PM
    Jniedbalski replied to a thread 2 molds 2 results in Cast Boolits
    Some of My lee molds and my two noe molds had this problem. My noe molds just needed heat cycled 4 or 5 times. The lee molds I took a small wood down and ran along the outside edges of each cavity and heat cycled them. They now just fall out rather...
    21 replies | 636 view(s)
  • Jniedbalski's Avatar
    03-30-2018, 04:11 PM
    Pm sent
    3 replies | 288 view(s)
  • Jniedbalski's Avatar
    03-29-2018, 10:22 PM
    7.62x38 lee nagant pistol dies and brass I have a lee 7.62x38 pistol 3 die set for sale. It was made for converting and loading32/20 brass. I have only used this set to load actual ppu 7.62x38 brass. It workes good for this. This set is not carbide...
    3 replies | 288 view(s)
  • Jniedbalski's Avatar
    03-24-2018, 05:33 PM
    I have always wanted to try longshot but haven’t yet. I thank it will be really good in the longer barrel of the carbine
    23 replies | 782 view(s)
  • Jniedbalski's Avatar
    03-24-2018, 03:21 PM
    If the brass didint explode from a double charge forcing the cylinder to blow apart it must be bad heat treat or metal in the cylinder. If the brass is still all together I do not see how it could be over loaded. The cylinder walls in the photo...
    60 replies | 2519 view(s)
  • Jniedbalski's Avatar
    03-24-2018, 02:49 AM
    All the Italian companies that make reproduction bp pistols all have undersized cylinders. Usually .005 to .007 thousand. Why I don’t know must be a reason. The only bp revolvers I have seen with cylinders the same size as grove diameter are the...
    61 replies | 1804 view(s)
  • Jniedbalski's Avatar
    03-24-2018, 12:07 AM
    I load the 40 S&w for a high point pistole and carbine. I use and cast the lee 175 tc and the 145 swc. I tried a lot of different powders all worked good.the best out of my carbine was with the lee 175 tc And the plated ranier 165 gr plated hp with...
    23 replies | 782 view(s)
  • Jniedbalski's Avatar
    03-23-2018, 11:40 PM
    The bullets I got from them are-very good. About two years ago I think when I got them
    12 replies | 485 view(s)
  • Jniedbalski's Avatar
    03-23-2018, 11:06 PM
    Sory I accidentally posted it here instead of swapping and selling. trying to deleat the post but canít figure how to do it. So if any mods find it please delete it for me . I have posted this in the correct spot thanks
    2 replies | 102 view(s)
  • Jniedbalski's Avatar
    03-23-2018, 10:53 PM
    I don’t know how I posted this here instead of swapping and selling but I did move it
    2 replies | 102 view(s)
  • Jniedbalski's Avatar
    03-23-2018, 10:42 PM
    7.62x38 lee nagant pistol dies and brass I have a lee 7.62x38 pistol 3 die set for sale. It was made for converting and loading32/20 brass. I have only used this set to load actual ppu 7.62x38 brass. It workes good for this. This set is not carbide...
    0 replies | 147 view(s)
  • Jniedbalski's Avatar
    03-23-2018, 09:58 PM
    I have a lee 7.62x38 pistol 3 die set for sale. It was made for converting and loading32/20 brass. I have only used this set to load actual ppu 7.62x38 brass. It workes good for this. This set is not carbide so the brass needs lubed when sizing....
    2 replies | 102 view(s)
  • Jniedbalski's Avatar
    03-22-2018, 10:57 PM
    Wonder why they don’t just use it for gravel roads. Must be sompthing in the rock the epa doesn’t want on the roads
    11 replies | 656 view(s)
  • Jniedbalski's Avatar
    03-22-2018, 03:22 PM
    Every body on this site should really watch this video
    11 replies | 656 view(s)
  • Jniedbalski's Avatar
    03-22-2018, 01:03 PM
    I have bought the Star BM Spanish police trade in. It is in very good shape like new.also shoots great. The Bretta 92fs Italian police trade in has holster wear but is also very good shape and shoots like it. The S&w model 64 4 in barrel stanless 38...
    20 replies | 703 view(s)
  • Jniedbalski's Avatar
    03-21-2018, 08:23 PM
    I just watched the video. Ism surprised lead is not 10$ a pound with the very long prosess. In the video the huge pile of talings is still there . When they say it’s a lot bigger than the great Piramids they are right. You can see the pile ten or...
    11 replies | 656 view(s)
  • Jniedbalski's Avatar
    03-21-2018, 08:15 PM
    I just watched the video. Ism surprised lead is not 10$ a pound with the very long prosess. In the video the huge pile of talings is still there . When they say it’s a lot bigger than the great Piramids they are right. You can see the pile ten or...
    11 replies | 656 view(s)
  • Jniedbalski's Avatar
    03-21-2018, 06:24 PM
    This is in my part of the state. Well 40 miles north of me and slightly west. I have heard from relatives that worked the lead mines from bunker mo that you can find lead ore just digging in your yard. Wish I could find some
    11 replies | 656 view(s)
No More Results
About Jniedbalski

Basic Information

Age
50
About Jniedbalski
Location:
SE MISSOURI
Interests:
SHOOTING RELOADING
Occupation:
Maintenance hvac

Statistics


Total Posts
Total Posts
170
Posts Per Day
0.22
General Information
Last Activity
Yesterday 09:47 PM
Join Date
03-16-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check