RepackboxInline FabricationTitan ReloadingRotoMetals2
MidSouth Shooters SupplyADvertise hereLee Precision

  • Jniedbalski's Avatar
    09-27-2020, 11:38 PM
    My range also. Just go to the pistole range and pick up lead up off the ground. I could probably pick up 400 to 500 lbs easy before I even needed to dig any
    19 replies | 303 view(s)
  • Jniedbalski's Avatar
    09-27-2020, 11:35 PM
    Each caliber would do good. If your 303 Brit shoots good use it.on lead hardness I don’t know never killed anything that big. I would think wheel weights mixed 50/50 with pure lead would do good
    22 replies | 1405 view(s)
  • Jniedbalski's Avatar
    09-27-2020, 09:27 PM
    The best surface to use your bullet puller on is hard concrete. I have tried softer surfaces like wood floor or table and it just doesnít work good. On over all leingth donít worry about it much. In a revolver as long as it fits and dosent stick out...
    138 replies | 1675 view(s)
  • Jniedbalski's Avatar
    09-19-2020, 08:19 PM
    . He is talking about Wd 40 brand of penetrating oil. It’s good stuff but ed’s red works just as good.
    40 replies | 870 view(s)
  • Jniedbalski's Avatar
    09-18-2020, 10:28 PM
    Is great in my 9 mm not sized. I got the Lee 358 105 I havenít shot yet but casted a bunch up. I use only white lable lube 45/45/10 or lee liquid alox. 3.5 to 4 gr of bulseye works great for 115 to 125 gr bullets. Only problem my high point likes...
    32 replies | 781 view(s)
  • Jniedbalski's Avatar
    09-18-2020, 10:23 PM
    My lee 158 125 Rf and the lee 356 120 tc is
    32 replies | 781 view(s)
  • Jniedbalski's Avatar
    09-17-2020, 11:30 PM
    I had a savage 112v single shot Varmit barrel in 220 swift. It was the best shooting gun I ever had. It had a 1 /12 or a 1 /14 twist heavy bbl. you could tape dimes on the target at 300 yards and shoot them off
    12 replies | 369 view(s)
  • Jniedbalski's Avatar
    09-17-2020, 11:11 PM
    . I have used this clear before and it looks just like the old Polly clear finish used years ago. 28 years ago I did a custom 6.5 jap stock Using PPG car clear and hardner And...
    13 replies | 371 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 09:39 PM
    Isint the lee .311 93 to small a diameter for a 8 mm Mauser? I use that bullet in a savage axis 308 with 3.2 of bullseye sized to .311. It shoots great.
    141 replies | 169669 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 12:40 PM
    I had one we picked up on a clean up week on the curb by the street.I didint thank it would be worth anything. It was in very nice shape. It went for over 600$ at a small auction.
    32 replies | 1015 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 12:05 PM
    The lead mines in Missouri are about 45 miles away from me. They have been mining there since the 1600’s
    48 replies | 1536 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 12:02 PM
    Check out the history of lead. This old video shows how Led ore was Converted to lead...
    48 replies | 1536 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 11:26 AM
    For auto pistole rounds I have very few Of the lee FCD sized down my bullets. The ones That do size down I only push the round in Past the carbide sizer just Enuf to get the bell To straighten Out. If I really want more crimp I just use my seater...
    34 replies | 850 view(s)
  • Jniedbalski's Avatar
    09-08-2020, 08:14 AM
    HS6 has worked for me in 38 loads with 158 gr boolets. Bulseye is my #1 powder in 38
    29 replies | 1375 view(s)
  • Jniedbalski's Avatar
    09-05-2020, 12:49 AM
    Jniedbalski started a thread 223 brass in Military Rifles
    Iam loading ,for me a large batch of brass. Prepping around 1000 rounds of mixed brass. How many times are you firing them? Using two different arís With below max loads With 55 gr fmjís. And 69 gr sierras.I know the primer pockets will usually get...
    12 replies | 551 view(s)
  • Jniedbalski's Avatar
    09-02-2020, 11:32 AM
    Necessary at 1200 FPS or less . The hot loads at 1400 will probably need it.
    6 replies | 691 view(s)
  • Jniedbalski's Avatar
    09-02-2020, 11:30 AM
    Thanks for the info. The real black or trail boss I didint even thank of. I will try trail boss for sure. The black I want to try but only have a little left. 1/2 a can or a bit more. Hard to get unless I do the 300 mile drive Total drive or mail...
    6 replies | 691 view(s)
  • Jniedbalski's Avatar
    08-31-2020, 08:34 AM
    Very nice rifle. I always liked the 22 trainers. I got a Chinese JW15 trainer that I like very well. It’s A pre import One and made a lot better than the ones that where imported the 90’s. It’s a tack driver.
    12 replies | 771 view(s)
  • Jniedbalski's Avatar
    08-30-2020, 02:12 PM
    My ely match smelled funny also. Almost like a plastic solvent. I only buy the augilaís in regular velocity. They seem as good as my cci or federal match.
    25 replies | 796 view(s)
  • Jniedbalski's Avatar
    08-30-2020, 01:14 AM
    Just got a new to me 44 mag traditions rifle. What do you all recommend for load or over all length? It has a 1/20 22 in heavy fluted barrel. The load that shoots great in it now is a 300 gr xtp loaded with imr 4227 at 19.5 gr. I want to start cast...
    6 replies | 691 view(s)
No More Results
About Jniedbalski

Basic Information

Age
52
About Jniedbalski
Location:
SE MISSOURI
Interests:
SHOOTING RELOADING
Occupation:
Maintenance hvac

Statistics


Total Posts
Total Posts
768
Posts Per Day
0.46
General Information
Last Activity
Today 12:54 AM
Current Activity
Viewing Thread Anyone know gunsmiths who will make custom cylinders for an X-Frame?
Join Date
03-16-2016
Referrals
0

1 Friend

  1. bajacoop bajacoop is offline

    Boolit Bub

    bajacoop
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check