MidSouth Shooters SupplyLee PrecisionTitan ReloadingADvertise here
RotoMetals2Graf & SonsStainLess Steel MediaInline Fabrication

  • Jniedbalski's Avatar
    04-20-2018, 02:54 PM
    I tried all the usual powders in the book. They all worked good for my pistole. In my hi point carbine Hs6 worked the best for slightly smaller groups. The lee 175 tc And the 165 gr plated xtream or Rainer hp plated bullet worked really good. I also...
    20 replies | 350 view(s)
  • Jniedbalski's Avatar
    04-13-2018, 10:42 PM
    The chamber is not 45/70. If it was a over pressure round it would shoot ,hard to extract or blow the gun up. The brass flowed out to fit the chamber. You can’t make the chamber that much bigger by shooting a high pressure load. It would shoot...
    16 replies | 565 view(s)
  • Jniedbalski's Avatar
    04-12-2018, 05:49 PM
    Jniedbalski replied to a thread Gas-Oh-Leen in Our Town
    Same here
    33 replies | 739 view(s)
  • Jniedbalski's Avatar
    04-11-2018, 05:35 PM
    Dixie gun works still I thank sell molds like this. They where actually women’s hair curlers. But Dixie just got different cherries and cut them out to make a mold
    6 replies | 249 view(s)
  • Jniedbalski's Avatar
    04-11-2018, 03:25 PM
    Stoning it off will be quick and easy a few minutes of time and it will be fine
    16 replies | 416 view(s)
  • Jniedbalski's Avatar
    04-08-2018, 12:53 AM
    There is nonthing wrong with the lee loder. It’s slow but who cares. It does load good ammo. You can load 50 to 100 rounds just sitting around after supper. With the dipper you are limited to only a few powders listed with the lee directions. This...
    24 replies | 709 view(s)
  • Jniedbalski's Avatar
    04-07-2018, 09:37 PM
    I have some 45 acp large primer brass up for sale. I have had this brass 5 or 6years but no 45.this is from a out door police and civilian range. Most of the brass was very clean and new when I picked it up. I have cleaned it with citric acid and...
    0 replies | 154 view(s)
  • Jniedbalski's Avatar
    04-07-2018, 12:36 AM
    I have for sale a lee 220 swift two die set. It is a collet neck sizing die and a dead length bullet seating die. I havenít used this die in 12 years . No longer have the gun. It comes with the shell holder and powder scoop and the round yellow...
    1 replies | 73 view(s)
  • Jniedbalski's Avatar
    04-06-2018, 08:38 PM
    In se Missouri we have a state ,conservation land and range that is free. The hunting area is over 1200 acres with three stocked fishing ponds. They also have a horse and walking trail, small camping areas.This runs along a big creek boat ramp ...
    54 replies | 1667 view(s)
  • Jniedbalski's Avatar
    04-02-2018, 03:25 PM
    Jniedbalski replied to a thread 2 molds 2 results in Cast Boolits
    Some of My lee molds and my two noe molds had this problem. My noe molds just needed heat cycled 4 or 5 times. The lee molds I took a small wood down and ran along the outside edges of each cavity and heat cycled them. They now just fall out rather...
    21 replies | 647 view(s)
  • Jniedbalski's Avatar
    03-30-2018, 04:11 PM
    Pm sent
    3 replies | 293 view(s)
  • Jniedbalski's Avatar
    03-29-2018, 10:22 PM
    7.62x38 lee nagant pistol dies and brass I have a lee 7.62x38 pistol 3 die set for sale. It was made for converting and loading32/20 brass. I have only used this set to load actual ppu 7.62x38 brass. It workes good for this. This set is not carbide...
    3 replies | 293 view(s)
No More Results
About Jniedbalski

Basic Information

Age
50
About Jniedbalski
Location:
SE MISSOURI
Interests:
SHOOTING RELOADING
Occupation:
Maintenance hvac

Statistics


Total Posts
Total Posts
171
Posts Per Day
0.22
General Information
Last Activity
Today 04:18 PM
Join Date
03-16-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check