StainLess Steel MediaRotoMetals2Titan ReloadingGraf & Sons
Lee PrecisionInline FabricationADvertise here

Tab Content
  • wlkjr's Avatar
    10-18-2017, 09:45 PM
    What pistol are you shooting them out of? I am using 3 different Glocks with Titegroup and a 147gr with Hi-Tek. The mold is from Accurate and has no lube grooves. I also previously use 147gr from Bayou without issue.
    27 replies | 576 view(s)
  • wlkjr's Avatar
    10-04-2017, 10:40 AM
    My question is what size do those boolits drop out at and how far down are you sizing them? I also use the Aqua Lube 5000 before sizing and it aids tremendously. I usually size after the second coat and if necessary coat a third time. I size my 147g...
    9222 replies | 1425781 view(s)
  • wlkjr's Avatar
    10-03-2017, 07:44 PM
    I mix mine in 60ml batches which is about enough to do two coats on 1500 .380 boolits with a little left over. I coated 2500 today in three different colors. The greens are the most sensitive to higher heat and longer cook times. It appears that the...
    9222 replies | 1425781 view(s)
  • wlkjr's Avatar
    10-02-2017, 07:52 PM
    I coated 1200 9mm 147 grainers today, half of those black and the other half candy apple red. My small bottle of Kryptonite green had gone bad. It had a brown coating I could see through the bottle. After shaking for several minutes, the brown...
    9222 replies | 1425781 view(s)
  • wlkjr's Avatar
    09-28-2017, 05:51 PM
    I'm back in business. My cord and connector came in today. The old socket connector was a 10a and the new one is rated at 20a. The new cord is 14ga and rated at 15a. So I cut a piece of spare SJ00 12ga cord and crimped on new ring connectors and...
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-27-2017, 12:30 PM
    I bought it used from a member here, but as far as I know, it is original, not counting the conversion to air assist.
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-27-2017, 11:25 AM
    I agree on the wire size. Stranded wire is suppose to carry more amps than solid, or so I have read in the past. But 12ga is for 20 amps, 14 for 15 amps, so I can't see 18 for more than 10amps. Since the Master Caster has a 14ga cord on it, that...
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-26-2017, 02:23 PM
    I think it was the undersized power cord and connector. The connector in the PID was only a 10 amp and the supply cord was 18 ga. The Master Caster has a 14 ga. cord and should not be plugged into a smaller cord from what I have always been told.
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-26-2017, 12:27 PM
    I found a 14ga cord and C20 male connector on Amazon that should work.
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-26-2017, 12:19 PM
    I'm trying to source a heavier cord that connects to a C20 male connector in the back of the PID, plus a new C20 male connector. I think I have located a connector at Auber. I have several spare cords that I could splice but I wanted to keep the...
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-26-2017, 11:07 AM
    19 replies | 610 view(s)
  • wlkjr's Avatar
    09-26-2017, 11:04 AM
    The PID on my Master Caster just bit the dust. I flipped the ON switch and was waiting for it to warm up and in about 3 minutes I heard a strange noise like paper rustling. It made this noise twice and then I saw lots of smoke coming out of the PID....
    19 replies | 610 view(s)
No More Results
About wlkjr

Basic Information

About wlkjr
Location:
Georgia

Statistics


Total Posts
Total Posts
216
Posts Per Day
0.36
General Information
Last Activity
Yesterday 11:03 PM
Join Date
02-24-2016
Referrals
0

1 Friend

  1. ferreira36 ferreira36 is offline

    Boolit Mold

    ferreira36
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check