ADvertise hereWidenersLee PrecisionInline Fabrication
Titan ReloadingRepackboxMidSouth Shooters SupplyRotoMetals2

Tab Content
  • GONRA's Avatar
    10-11-2019, 05:42 PM
    GONRA believes you will get a lot of Professional Replies. Just make SURE to purchase a "screw cutting metal cutting lathe" WITH A LEAD SCREW!!! Don't waste yer $$$ on anything else....
    5 replies | 351 view(s)
  • GONRA's Avatar
    10-11-2019, 05:34 PM
    GONRA replied to a thread New Lee Locknuts in Reloading Equipment
    Sure look great to GONRA! Will get some on next MIDWAY order.
    43 replies | 1375 view(s)
  • GONRA's Avatar
    10-10-2019, 05:54 PM
    GONRA sez - USE YER HEAD - do any "difficult case prep" on a Huge Single Stage Press. >>> Progressive Presses are NOT designed to do Hard Core Case Prep! <<< Check EACH NECKED CASE headspace with a gage! THEN run PROPERLY PREPPED cases...
    17 replies | 1518 view(s)
  • GONRA's Avatar
    10-10-2019, 05:29 PM
    GONRA suggests (warm up yer cheque book!) just purchase Grafs 8mm Nambu brass! Should be WAY BETTER than anything you can womp up..... (Decades ago, made 8mm Nambu brass from all sorts of host brass. Verked Just Fine. BUT - its LOTTSA ...
    11 replies | 1014 view(s)
  • GONRA's Avatar
    10-08-2019, 05:37 PM
    Sounds like n10sivern is gonna have one hellava reloading Bench! (Hope yer gonna take time to GLUE all the joints!) Rigidity is the name of the game here. Read on... GONRA suggests you MAKE SURE to have plenty daylite under each future bench...
    41 replies | 1100 view(s)
  • GONRA's Avatar
    10-07-2019, 05:41 PM
    GONRA is happy with a RCBS Electronic Chargemaster - then touching up / checking up with a beam balance scale / dribbler.
    42 replies | 2127 view(s)
  • GONRA's Avatar
    10-05-2019, 07:08 PM
    GONRA replied to a thread Powder containers in Our Town
    GONRA suggests wide mouth peanut butter jugs (believe its a good plastic? You'll have to check! I know they hold gasoline Just Fine!) Metal 2 cycle gas jugs with screw on tops should be GREAT!
    32 replies | 1279 view(s)
  • GONRA's Avatar
    10-05-2019, 05:51 PM
    GONRA replied to a poll Which press do you use? in Our Town
    GONRA notes ya'll havalotta presses. Be SURE to use yer LARGEST PRESS for "case prep". (Very Important on necked rifle calibers to get uniform headspace! STP Oill Treatment or Trii-Flow Synthetic Grease case lube is necessary too!) Many...
    89 replies | 3830 view(s)
  • GONRA's Avatar
    10-03-2019, 06:43 PM
    GONRA has lottsa olde reloading manuals / powders. BUT - ALWAYS "start out" with the POWDER MANUFACTURER'S manual whenever possible!
    28 replies | 938 view(s)
  • GONRA's Avatar
    10-02-2019, 05:14 PM
    GONRA replied to a thread To lube or not to Lube in Boolit Lube !
    GONRA suggests Jevyod get a lubrisizer to "lube/size right" (correctly!) for decent / meaningful comparison. UNFORTUNATELY cannot "cheap out" on this stuff....
    11 replies | 1014 view(s)
No More Results
About GONRA

Basic Information

Statistics


Total Posts
Total Posts
510
Posts Per Day
0.37
General Information
Last Activity
10-14-2019 10:08 PM
Join Date
01-24-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check