RotoMetals2Lee PrecisionMidSouth Shooters SupplyInline Fabrication
Titan ReloadingWidenersADvertise hereRepackbox

Tab Content
  • GONRA's Avatar
    Today, 05:50 PM
    Few years ago, GONRA verked on a large quantity of Scrap Dealer .50 BMG brass. Ended up with lottsa scrap, BUT 1200 properly prepped cases: First made an case dial indicator wall thickness measuring setup. (First class - "a roller & a ruby"!) ...
    6 replies | 180 view(s)
  • GONRA's Avatar
    05-25-2020, 10:42 PM
    GONRA replied to a thread Unknown gunwriter in Vintage Gun Books
    GONRA sez 7.62x38mm Berdan primed brass and separate FMJ bullets were sold to cartridge collectors back in 1960's, probably much earlier. Veeery close to the modern 7.62x39mm Soviet cartridge. (Am SURE one could load 'em and shoot in Soviet...
    14 replies | 3272 view(s)
  • GONRA's Avatar
    05-25-2020, 06:45 PM
    GONRA suggests winelover try Blue Dot. Pretty sure you'll like it!
    48 replies | 1332 view(s)
  • GONRA's Avatar
    05-22-2020, 10:59 PM
    GONRA replied to a thread Metal Work in Our Town
    GONRA sez - better make a mandrel to mount the tube on. Trick is to avoid wall collapse / bad OD uniformity. Gottahava mandrel.... (Not sure any readers really understand yer project..... I sure don't!) ???? But if ya'll still REALLY wanna...
    14 replies | 603 view(s)
  • GONRA's Avatar
    05-12-2020, 07:16 PM
    GONRA sez - listen to everybody - slug the bore and use a really nice DIGITAL micrometer for Groove diameters. Also, listen to John Boy and get a set of Pin Gages for Bore diameters.
    29 replies | 3029 view(s)
  • GONRA's Avatar
    05-08-2020, 05:52 PM
    jonp - GONRA successfully uses Blue Dot for .44 Mag, .44 AUTO MAG and .45 Win Mag. Where's the Blue Dot problem? Some jerk who shouldn't be hand loading in the first place?
    24 replies | 693 view(s)
  • GONRA's Avatar
    05-06-2020, 07:23 PM
    Three44s - GONRA uses HS-6 for 9mm UZI SMG blasting. Use 231 for subsonic suppressed blasting though. (Sounds like a woodpecker!)
    38 replies | 2499 view(s)
  • GONRA's Avatar
    05-06-2020, 07:05 PM
    GONRA found "STP Oil Treatment" or "Tri Flo Synthetic Grease" both suit the most difficult / beatup "scrap dealer" .50 BMG and 14.5x114mm Soviet Lacquered Steel Case Chicom "case preps". >>> We're talkin' FULL LENGTH...
    68 replies | 74931 view(s)
  • GONRA's Avatar
    05-04-2020, 05:43 PM
    GONRA weighs everything with my RCBS ChargeMaster then puts pan back onto its Beam Balance to double check. (Just being paranoid as usual.) For smaller charges, DO NOT FORGET to it put a small nail (or wotever) marker in the charged case so...
    9 replies | 1099 view(s)
  • GONRA's Avatar
    05-04-2020, 05:28 PM
    GONRA wonders if ANYBODY has outgefiggered how to "measure" 800X powder? Perfect for my .45 ACP 1928 Thompson SMG but have to weigh every charge on my Dillion 650. @#$%^
    38 replies | 2499 view(s)
  • GONRA's Avatar
    05-02-2020, 08:27 PM
    GONRA enjoyed Sharps book waaaay back. Got me going on Hollywood reloading stuff.... Also Roy Dunlap's "Ordnance Went Up Front" which is REALLY GREAT... Just seemed a LOT better than Gun Mag stuff at the tyme....
    24 replies | 5751 view(s)
  • GONRA's Avatar
    05-02-2020, 06:55 PM
    GONRA sez - maybe ya'll just wanna keep "yer gun library" to read (over and over again) when yer shootin' days are over and yer Just Sittin' there drinking beer and watching TV? ??? Think about it!
    27 replies | 3070 view(s)
  • GONRA's Avatar
    05-01-2020, 07:07 PM
    DECADES AGO - GONRA loaded lottsa .25 ACP with Ideal 252435 cast lead 50 grain, .253 inch diameter boolits. Had to make my own lube sizer dies. Still shoots great in a variety of European .25 ACP autos.
    16 replies | 2462 view(s)
  • GONRA's Avatar
    05-01-2020, 05:57 PM
    too many things - GONRA's 125 grain .284 inch Herter's Bullets were conventional in every sense. Can closely dup GI .276 Pedersen ammo with these..... (Do hava vague memory reading about "wasp waist" bullet BS in Herter's Catalogs though!)...
    9 replies | 5640 view(s)
No More Results
About GONRA

Basic Information

Statistics


Total Posts
Total Posts
609
Posts Per Day
0.38
General Information
Last Activity
Today 06:57 PM
Join Date
01-24-2016
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check