StainLess Steel MediaRotoMetals2Lee PrecisionMidSouth Shooters Supply
Inline FabricationGraf & SonsADvertise hereTitan Reloading

Tab Content
  • vzerone's Avatar
    Today, 12:47 PM
    Rifle: 1909 Argentine Groove: .3110 Brass: 30-06 Rem sized down to 7.65 Argentine with no special work done to it. Powder: Alliant RL-22 Charge: 45.0 grains Primer: CCI Large Rifle Standard (I don't like them) Temperature: 44 Degrees...
    9 replies | 435 view(s)
  • vzerone's Avatar
    Yesterday, 02:39 PM
    Part of the rest of the story: https://www.africahunting.com/threads/wdm-bell-his-elephant-hunting-rifles.15057/ As noted Bell most often used FMJ or military bullets and placed the shot precisely.
    18 replies | 386 view(s)
  • vzerone's Avatar
    Yesterday, 02:24 PM
    vzerone replied to a thread Hollowpoint failure in Cast Boolits
    I think many have the wrong idea of how a cast hollow point should work from a pistol/revolver for the bigger game such as deer. You want that hollow point to open and mushroom only after it has initially entered the body right upon entering the...
    20 replies | 442 view(s)
  • vzerone's Avatar
    04-21-2018, 11:43 PM
    They aren't pinned!!!
    9 replies | 312 view(s)
  • vzerone's Avatar
    04-21-2018, 04:52 PM
    Why would a five groove be any different? They drill the hole, ream it and hone it and that's your bore. So it would have the same bore as 4/6/etc groove barrels. Micro Groove is slightly different. All you need is a V block to use with you mic...
    9 replies | 312 view(s)
  • vzerone's Avatar
    04-21-2018, 09:26 AM
    I have to agree with you Lloyd. Razor Dobbs killed two cape buffaloes with a 5 inch barreled Sig 1911 in 10mm. He had through and through penetration on both of them and was using, I believe, Sledgehammer hard cast. I watched it on video and can...
    69 replies | 1663 view(s)
  • vzerone's Avatar
    04-16-2018, 07:13 PM
    Huh, I was of the belief that the wind pushes the whole bullet to the direction it's blowing rather then turning the nose to that direction. If it turned the nose Wow could you imagine how far off target the bullet would be then? Think about it,...
    30 replies | 779 view(s)
  • vzerone's Avatar
    04-16-2018, 12:25 PM
    Don'tcha know you are suppose to bring a plum bob or level with ya when setting up a target?? :kidding::kidding::kidding:
    30 replies | 779 view(s)
  • vzerone's Avatar
    04-16-2018, 09:56 AM
    Waco you're getting there, but a few things concern me. Was your target backer board plumed vertically? I ask because a good number of your bullet holes look like they hit at an angle. It's either that or your bullets were yawing/not stabilized. ...
    30 replies | 779 view(s)
No More Results
About vzerone

Basic Information

Statistics


Total Posts
Total Posts
1,395
Posts Per Day
1.61
General Information
Join Date
12-09-2015
Referrals
1

7 Friends

  1. JonB_in_Glencoe JonB_in_Glencoe is offline

    Moderator

    JonB_in_Glencoe
  2. kfd518 kfd518 is offline

    Boolit Man

    kfd518
  3. M-Tecs M-Tecs is offline

    Boolit Master

    M-Tecs
  4. Moleman- Moleman- is offline

    Boolit Master

    Moleman-
  5. runfiverun runfiverun is offline

    Banned

    runfiverun
  6. Texas by God Texas by God is offline

    Boolit Master

    Texas by God
  7. waksupi waksupi is offline

    Moderator Emeritus / Trusted loob groove dealer

    waksupi
Showing Friends 1 to 7 of 7
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check