Inline FabricationRepackboxTitan ReloadingMidSouth Shooters Supply
Lee PrecisionADvertise hereRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • Drew P's Avatar
    09-18-2019, 12:47 AM
    Curious why people dislike the safety? Itís very tiny, and it works. Whatís not to like?
    31 replies | 1028 view(s)
  • Drew P's Avatar
    09-17-2019, 02:28 PM
    Drew P replied to a thread My Rossi 92 project in Leverguns
    Not sure what it is, I was able to find it at my local gunsmith in his bin of stuff. It’s about .250 taller than stock tho.
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-17-2019, 02:27 PM
    Drew P replied to a thread My Rossi 92 project in Leverguns
    45 colt
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-16-2019, 02:50 PM
    Drew P replied to a thread My Rossi 92 project in Leverguns
    Yeah I was applying a coat per day for a while until it slowed it’s absorbing so that might be why, I had read that coats take 24 hrs to dry, “sometimes longer” but not very specific. Since I live in a fairly low humidity area I figured I would be...
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-16-2019, 12:53 AM
    177$ doesn’t get you too far at the gunsmiths trying to make the Rossi work. So unless you are a gunsmith or are sleeping with one, get the Henry.
    31 replies | 1028 view(s)
  • Drew P's Avatar
    09-13-2019, 10:42 PM
    Drew P replied to a thread My Rossi 92 project in Leverguns
    You can use a neon sign transformer too, which is much higher voltage, and also much safer. If you get shocked by a neon transformer, you’ll *probably* live to tell the tale. However the microwave unit will kill you dead. So, proceed with CAUTION!...
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-13-2019, 10:39 PM
    Drew P replied to a thread My Rossi 92 project in Leverguns
    Hoping to get a little more gloss in the finish eventually. But this girl needs to do some safe time for a few months to let the finish harden
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-13-2019, 10:08 PM
    Drew P started a thread My Rossi 92 project in Leverguns
    I wanted to share this project as Iíve been working pretty hard on it and itís turned out killer. It started life as a rossi ranch hand, then got SBRíd and buttstock extended with some pine, then to hide the ugly pine I made a leather boot. New...
    15 replies | 512 view(s)
  • Drew P's Avatar
    09-09-2019, 02:03 PM
    My only loaded gun at home is a 12ga pump, which I keep empty chamber. Well, while I was gone one day my gf decided to play with it, pumping the action ďbecause it sounds coolĒ. Then she ventilated my floor with a rather large hole. Brand new...
    87 replies | 3203 view(s)
  • Drew P's Avatar
    09-06-2019, 06:01 PM
    Funny, complaints about the aesthetic of this rifle are confusing to me. I do believe looks matter, and I wouldn’t own the hipoint for this reason. However I feel this ruger is not only not ugly, but actually quite attractive. Dunno, but it’s...
    329 replies | 34665 view(s)
  • Drew P's Avatar
    08-28-2019, 02:33 AM
    If your hands get sweaty then forget about most of these mentioned. G10 and rubber are your best choices. Or micarta, or carbon, which is functionally the same as g10. I love g10! You can even get it to look like wood, which Iíve done on my...
    44 replies | 1294 view(s)
  • Drew P's Avatar
    08-26-2019, 11:43 AM
    More range testing yesterday and some interesting failures. First of all the fore grip almost fell off after the screw tried to make an escape. Not big deal. But several FTF and looked like light primer strikes. Seemed like they were somewhat...
    329 replies | 34665 view(s)
  • Drew P's Avatar
    08-24-2019, 05:14 PM
    I clean the Poops out of my mp molds, soap, water, alcohol, brake cleaner, Iíve tried them all. It usually seems to take a few sessions to make them sing. There must be something in there that just wonít come out otherwise.
    43 replies | 2584 view(s)
  • Drew P's Avatar
    08-23-2019, 09:58 PM
    Looked hard at these but .32 is the ONE cartridge I shoot, but don’t load. So, yes, it would get expensive for me too if I bought one. Probably hold out for a 92S instead. I’d also be interested in a single action beretta which I know exists but...
    64 replies | 2297 view(s)
  • Drew P's Avatar
    08-23-2019, 03:27 PM
    Drew P replied to a thread Hi Point Carbine in Factory Rifles
    I’ve seen a few of these for sale used lately for around 100$!
    99 replies | 8241 view(s)
  • Drew P's Avatar
    08-23-2019, 03:25 PM
    Drew P replied to a thread NAA Guardian Jamming in Cast Boolits
    My GF will only tolerate a few hundred times at max lol.
    46 replies | 1417 view(s)
No More Results
About Drew P

Basic Information

About Drew P
Location:
NW USA
Occupation:
Casterbator

Statistics


Total Posts
Total Posts
853
Posts Per Day
0.61
General Information
Last Activity
Yesterday 11:02 AM
Join Date
11-17-2015
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check