Lee PrecisionRepackboxRotoMetals2ADvertise here
WidenersMidSouth Shooters SupplyTitan ReloadingInline Fabrication

Tab Content
  • MaLar's Avatar
    11-16-2019, 08:30 PM
    Corned venison is VERY GOOD!
    37 replies | 531 view(s)
  • Dragonheart's Avatar
    11-03-2019, 01:46 AM
    I only use gas check on rifle bullets. I double coat rifle bullets, leaving the check base uncoated on the first coat, installing the check then then a second PC on the complete bullet, which bonds the check like it is part of the bullet. I PC all...
    6 replies | 344 view(s)
  • Dragonheart's Avatar
    11-03-2019, 01:36 AM
    I have fired a number of full power 22-250 plain base PC bullets at 3500+ fps with no leading as well as full power 7x57, 30-06, 7.72x39, .556. A properly coated PC bullet will withstand the torque spinup of 50K chamber pressure, so as far as I am...
    6 replies | 330 view(s)
  • Dragonheart's Avatar
    11-03-2019, 01:27 AM
    When I built my 30" PC oven I used a PID because the oven controls were shot and the reason I got the oven for free. Otherwise I see no need for a PID if an oven will get to 400 degrees and hold a reasonable constant temp once its there, because...
    20 replies | 1433 view(s)
  • Bama's Avatar
    10-28-2019, 07:29 PM
    I use 3/16 aluminum plate that fits the original shelf with a sheet of oven liner on top I only pull out the shelf a couple of inches and stand bullets up with a pair of tweezers if bases are flat not a problem to stand bullets, only knock over if I...
    84 replies | 37069 view(s)
  • Bama's Avatar
    10-23-2019, 06:00 PM
    May be shell holder got mixed up from another die set. Found out the hard way they are not all the same thickness above shell rim. Had to take a couple of thousands from to to fix problem and started keeping matched dies and shell holders together.
    25 replies | 872 view(s)
  • Bama's Avatar
    10-22-2019, 02:50 AM
    Been doing it for 20 years. Works well with non military brass. Miliitary brass is thicker and the froward section of case does not want to release from chamer without occasional problems. Non military brass works great and is reloadable. It is...
    46 replies | 22789 view(s)
No More Results
About Bama

Basic Information

About Bama
Biography:
Hand loading for 41 years
Location:
Alabama
Interests:
Handloading,Machinist
Occupation:
Retire Engineer

Statistics


Total Posts
Total Posts
412
Posts Per Day
0.28
General Information
Last Activity
10-29-2019 06:16 PM
Join Date
11-11-2015
Referrals
0

2 Friends

  1. Dragonheart Dragonheart is offline

    Boolit Master

    Dragonheart
  2. MaLar MaLar is offline

    Boolit Buddy

    MaLar
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check