Titan ReloadingMidSouth Shooters SupplyLee PrecisionRepackbox
RotoMetals2Inline FabricationADvertise here

Tab Content
  • ShooterAZ's Avatar
    10-26-2020, 08:57 PM
    Personally, I'd want to have those parts in my rifle. I'd bet Timney would send them to you, no problem. They are good people to deal with in my experience. I like their triggers too, I have a few of them in different models of rifles and all...
    4 replies | 150 view(s)
  • ShooterAZ's Avatar
    10-22-2020, 10:50 AM
    Yes, I also read it as conventional lube...not PC. In that instance I will wipe as much powder off as I can with a rag, then throw them into a cold pot and proceed to melt them down. A few grains of powder, no big deal.
    9 replies | 210 view(s)
  • ShooterAZ's Avatar
    10-22-2020, 09:28 AM
    I'm down this year for sure, in a "normal year" I'd be over 10K but less than 25K.
    33 replies | 1092 view(s)
  • ShooterAZ's Avatar
    10-13-2020, 11:22 AM
    I've not had any of the problems you mentioned with mine. Over the years the only things I needed to do was replace the hammer spring, and I replaced the base pin with a Belt Mountain pin. The original base pin would start slide to out under recoil....
    56 replies | 2154 view(s)
  • ShooterAZ's Avatar
    10-12-2020, 08:42 PM
    ShooterAZ replied to a thread Newby questions in Cast Boolits
    .311 is what I normally size just about all of my 30 Cal cast boolits to. The one exception would be 30 Carbine, which gets sized to .309. Hopefully you'll be able to get your Lee 309 molds to cast at least .311. Some of my Lee molds will, some...
    8 replies | 239 view(s)
  • ShooterAZ's Avatar
    10-12-2020, 07:02 PM
    I keep rifle cases separate. One of the great things about cast boolits in rifles is that most loads are pretty mild, pressure wise. Once I feel that my jacketed bullet cases are exhausted (for lack of a better term), I will relegate them to use...
    10 replies | 375 view(s)
  • ShooterAZ's Avatar
    10-06-2020, 10:49 AM
    Arizona has the same lead free recommendation. It's primarily in the hunt units that are adjacent to the Grand Canyon. They re-introduced the California Condor at the Canyon, and the condors love to eat lead laden gut-piles. It's not law, just...
    25 replies | 1543 view(s)
  • ShooterAZ's Avatar
    10-05-2020, 06:00 PM
    Prime Rib Dip, with mushrooms and melted Swiss cheese....Yum.
    74 replies | 1778 view(s)
  • ShooterAZ's Avatar
    10-03-2020, 02:24 PM
    I needed to put a taller front sight on one of my Win M94's when I put a Williams rear sight on it. That would be one example.
    7 replies | 293 view(s)
  • ShooterAZ's Avatar
    10-03-2020, 10:13 AM
    ShooterAZ replied to a thread pump accuracy in Rimfire Area
    I have a Winchester model 62A that shot patterns when I first got it. The original owner fed it a steady diet of shot loads and never cleaned it. The bore looked like a smooth bore. After hours of soaking and scrubbing, the bore finally came clean....
    21 replies | 868 view(s)
More Activity
About 2400

Basic Information

About 2400
Location:
Northern AZ

Signature


M.O.P.H.--D.A.V.-- N.R.A.-- Life Member

Statistics


Total Posts
Total Posts
71
Posts Per Day
0.02
General Information
Last Activity
09-13-2020 02:23 PM
Join Date
12-18-2007
Referrals
2

4 Friends

  1. 700CDL 700CDL is offline

    Boolit Mold

    700CDL
  2. HollandNut HollandNut is offline

    Galena Guru

    HollandNut
  3. JTknives JTknives is offline

    Boolit Master

    JTknives
  4. ShooterAZ ShooterAZ is offline

    Moderator

    ShooterAZ
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check