MidSouth Shooters SupplyInline FabricationGraf & SonsLee Precision
WidenersRepackboxRotoMetals2Titan Reloading

  • Outpost75's Avatar
    Today, 01:13 PM
    Fore-end hanger should not touch barrel. Common technique to "free float" barrel on No.1 is to drive a wedge between the hanger and barrel to bend it away slightly from the barrel and to pull the wedge out. Adjust bend until you can slide a...
    1 replies | 57 view(s)
  • Outpost75's Avatar
    Today, 11:07 AM
    One of the rarest US milsurps is also a levergun
    4 replies | 50 view(s)
  • Outpost75's Avatar
    Today, 10:47 AM
    That would support an e-Book!
    568 replies | 214932 view(s)
  • Outpost75's Avatar
    Yesterday, 08:24 PM
    Some .32 S&W Long Data which will help in working up loads for your Ruger: .32 S&W Long Factory Vs. Handloads In Revolvers and Rifle Remington cases, Federal 200 primers in all handloads: Ammo Type____________Colt DS 2________Colt PP...
    12 replies | 149 view(s)
  • Outpost75's Avatar
    Yesterday, 07:18 PM
    Agree that the Mods could lock and archive this thread. There are other threads addressing loading of the various .32 cartridges for field and recreational use, and perhaps those could be merged. I would like to see a new sticky combining all of...
    568 replies | 214932 view(s)
  • jimkim's Avatar
    Yesterday, 06:50 PM
    I love it! Thanks! Sent from my VS880 using Tapatalk
    4 replies | 114 view(s)
  • jimkim's Avatar
    Yesterday, 06:46 PM
    jimkim replied to a thread Dillon RL300 in Reloading Equipment
    The tubes that I got with mine were plastic. I was later told they are filler tubes. I still think they are the originals. Why would you fill a tube, and use it to fill a second tube. That makes no sense. By the way, you STOLE that press. Sent...
    3 replies | 124 view(s)
  • Outpost75's Avatar
    Yesterday, 04:54 PM
    You are correct. Initial work was done in .32 S&W Long brass making essentially a +P load, but Mike Bussard at Federal Cartridge, and Jay Jarvis at Ruger both convinced Ted Rowe at H&R that it would be best to lengthen the case slightly to prevent...
    568 replies | 214932 view(s)
  • Outpost75's Avatar
    Yesterday, 02:43 PM
    If properly stored, USGI Ball M1, Ball M2 and APM2 ammunition of WW2 manufacture should still be 100% reliable. I am still using FA and LC ammunition made in the 1940s, which has produced normal pressure, velocity and accuracy, functioning reliably...
    11 replies | 298 view(s)
  • Outpost75's Avatar
    Yesterday, 11:45 AM
    Around here even the WW2-era corrosive ammo brings $1 per round. More than that if packed in the 8-round M1 Garand enbloc clips and bandoliers. If clipped pack figure $1 per round plus $2 per clip. WW2 dates are more collectible and if in clean...
    11 replies | 298 view(s)
  • Outpost75's Avatar
    Yesterday, 11:18 AM
    Good info from the posters above. I have owned both the S&W and Colt M1917s. The shallow rifling isn't usually an issue with correct bullets which "fit" IF the bore is in good condition. The biggest factor influencing accuracy of these guns is...
    28 replies | 335 view(s)
  • Outpost75's Avatar
    Yesterday, 10:55 AM
    I checked checked my references and you are indeed correct and I appreciate the correction. It can be dangerous to rely upon memory once you get past age 70. Thank you! But for the purpose of answering the OP, his 18" twist is more than ample.
    42 replies | 677 view(s)
  • Outpost75's Avatar
    Yesterday, 10:52 AM
    Outpost75 replied to a thread 38 Loads in Cast Boolits
    Back in the day (1960s-70s) many eastern police departments had "full charge" wadcutters factory loaded for practice ammunition. The purpose for doing so was to approximate the recoil of the old 158-grain lean roundnosed ammo which was carried back...
    8 replies | 243 view(s)
  • RP's Avatar
    03-16-2019, 09:36 PM
    After looking this thread over it looks like Location storage and weather are the problems.
    23 replies | 676 view(s)
  • Outpost75's Avatar
    03-16-2019, 06:13 PM
    My R-P .30-30 brass is 0.010"-0.011" which is normal in my experience for the caliber. I think somebody must have neck-turned some of yours and got a little "happy" with it. Did you use a tubing micrometer or ball mic to measure the necks or...
    6 replies | 124 view(s)
  • MaLar's Avatar
    03-16-2019, 02:05 AM
    Never hit a hammer with another hammer or some hardened metal. They can shatter! I carry a piece of an easyout in my arm. Was tapping the easy out in a drilled broken off bolt in an engine block when the hammer head broke into pieces.
    18 replies | 313 view(s)
  • RP's Avatar
    03-15-2019, 11:22 PM
    RP replied to a thread ar parts in Coatings and Alternatives
    I PC my PTR 91 looks good and works fine have not done any AR parts as of yet. I have some old 20 round mags that are just about bare metal I am going to coat.
    8 replies | 233 view(s)
  • jimkim's Avatar
    03-15-2019, 01:56 PM
    Swagerman shortened the ram. He also lengthened the toggle. The shorted ram allowed him to get the lever into a position in which the leverage was much higher, than at the bottom of the stroke. Sent from my VS880 using Tapatalk
    19 replies | 356 view(s)
  • Outpost75's Avatar
    03-14-2019, 09:43 PM
    Velocity Test Data for 7.62x25 in TT33 Pistol Handloads in Starline cases with CCI500 primers Ammunition Description_________________Vel@15ft., Sd, ES n=10 ____________________________________TT33, 4.6” Romanian Type P Ball, Factory 22,...
    20 replies | 304 view(s)
  • Outpost75's Avatar
    03-14-2019, 08:51 PM
    The Ruger carbine has a SAAMI chamber. For a 9mm carbine to function with anything you want a NATO chamber cut to the NATO Standardization Agreement 4090. Alternately, if you want to simply rethroat then use a Clymer .35 cal. rifle...
    12 replies | 209 view(s)
  • jimkim's Avatar
    03-14-2019, 06:36 PM
    It has a 1 1/8" diameter ram. Sent from my VS880 using Tapatalk
    19 replies | 356 view(s)
  • Outpost75's Avatar
    03-14-2019, 06:01 PM
    Outpost75 replied to a thread S&w in Cast Boolits
    Casting a lead lap in the barrel gives you better control of the process. My experience has been that fire lapping tends to cause forcing cone erosion more than lapping the tops of the lands where you want to remove the constriction. When I...
    13 replies | 350 view(s)
  • Outpost75's Avatar
    03-14-2019, 05:01 PM
    Outpost75 replied to a thread S&w in Cast Boolits
    You need to have a gunsmith inspect your barrel with gage pins for "thread choke." This is a constriction of the barrel shank at the root of the thread, caused by over-torquing the barrel when assembled into the frame. Very common with S&Ws. It...
    13 replies | 350 view(s)
More Activity
About runfiverun

Basic Information

About runfiverun
Location:
soda springs Id.

Statistics


Total Posts
Total Posts
28,096
Posts Per Day
6.84
General Information
Last Activity
03-14-2018 10:19 PM
Join Date
12-17-2007
Referrals
8

29 Friends

  1. 45nut 45nut is offline

    Cast Boolits Founder/B.O.B.

    45nut
  2. Bob Krack Bob Krack is offline

    Boolit Master at Heavens Range

    Bob Krack
  3. bruce drake bruce drake is offline

    Boolit Master

    bruce drake
  4. BSalty BSalty is offline

    Boolit Man

    BSalty
  5. bushwack bushwack is offline

    Boolit Bub

    bushwack
  6. DeputyDog25 DeputyDog25 is offline

    Boolit Buddy

    DeputyDog25
  7. Down South Down South is offline

    Boolit Master & Generous Contributor

    Down South
  8. eljefeoz eljefeoz is offline

    Boolit Buddy

    eljefeoz
  9. fishhawk fishhawk is offline

    Moderator Emeritus

    fishhawk
  10. goodsteel goodsteel is offline

    Boolit Grand Master

    goodsteel
Showing Friends 1 to 10 of 29
Page 1 of 3 123 LastLast
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check