Titan ReloadingGraf & SonsRotoMetals2Repackbox
WidenersMidSouth Shooters SupplyLee PrecisionInline Fabrication

Tab Content
  • KenT7021's Avatar
    03-17-2019, 07:18 PM
    KenT7021 replied to a thread M17 in 303? in Military Rifles
    U.S.Rifle Model 1917.As far as the rifle in question I would do a chamber cast.It can be chambered for almost anything.When DP P14's were available for $25.00 to $35.00 I built a number of rifles on them.Whether I used a P14 bolt or an M1917 bolt...
    24 replies | 640 view(s)
  • KenT7021's Avatar
    03-12-2019, 06:29 PM
    Check Amazon for the arbor shim assortment I posted about above.You'll have control over the thickness.
    29 replies | 739 view(s)
  • KenT7021's Avatar
    03-07-2019, 07:09 PM
    I have used a spacer for loading .38 Spl/,367 Mag.It works fine.I currently have an arbor shim assortment I bought from Amazon that allows better control of the thickness needed.I use them when using dies for cartridges they weren't for.
    29 replies | 739 view(s)
  • KenT7021's Avatar
    03-05-2019, 05:52 PM
    I use the Lyman 356402 in the 9mm.Most of my 9mm use is in P-08 Lugers and that bullet never causes a feeding problem.
    18 replies | 632 view(s)
  • KenT7021's Avatar
    03-04-2019, 06:25 PM
    I have Forster,L.E.Wilson,and a couple of the Lyman trimmers with the quick action chuck.I also have some file trim dies.They all have different ways of holding the case.They all work.I like the Lyman trimmers over the other two mentioned.I don't...
    19 replies | 627 view(s)
  • KenT7021's Avatar
    03-03-2019, 08:25 PM
    I must have overlooked the hate posts.I don't powder coat and have no interest in doing so.I don't tumble lube either and haven't pan lubed since I bought my first lube sizer.I am simply happy with my lube sizers.Anyone else is free to do what they...
    48 replies | 2170 view(s)
  • KenT7021's Avatar
    03-02-2019, 06:15 PM
    At one time all solid base Idea and Lyman molds could be ordered as hollow points.The only marking indicating a hollow pint mold was on the box.
    16 replies | 644 view(s)
  • KenT7021's Avatar
    02-26-2019, 01:48 PM
    KenT7021 replied to a thread Foaming Lead in Lead and Lead Alloys
    The danger from battery lead is the dross.If the dross comes in contact with moisture stibine gas is formed.This is a form of nerve gas.The NRA Handloaders Guide or Cast Bullet book had an article on it.It involved a fatality.
    25 replies | 1183 view(s)
  • KenT7021's Avatar
    02-25-2019, 12:01 AM
    I have eight reloading presses.Four of them are turret presses.I like the turret presses.I have never considered speed in reloading.I reload for economy and for precision.I also reload because a number of cartridges I reload are not available...
    66 replies | 2545 view(s)
  • KenT7021's Avatar
    02-22-2019, 01:16 PM
    I would not remove the main shaft.Mask it off if you want to paint.I have two with the original paint which looks well used and chipped.I have never considered repainting them.They work fine the way they are.
    4 replies | 241 view(s)
  • KenT7021's Avatar
    02-20-2019, 03:48 PM
    The new RCBS pot and the Lyman Mag25 are both made in China.My Mag25 hasn't had any problems.
    24 replies | 1313 view(s)
No More Results
About KenT7021

Basic Information

About KenT7021
Location:
Tacoma,Wa.

Statistics


Total Posts
Total Posts
434
Posts Per Day
0.33
General Information
Last Activity
Yesterday 05:28 PM
Join Date
08-21-2015
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check