MidSouth Shooters SupplyStainLess Steel MediaGraf & SonsADvertise here
Lee PrecisionInline FabricationTitan ReloadingRotoMetals2

  • leebuilder's Avatar
    01-14-2018, 09:23 PM
    You are correct the o ring wont have to used again as the casing is fire formed to your chamber, provided it's neck sized properly. IVI is Canadian ammo 1997 and 1992. The brass is ok some years it's top notch, thick at the bottom and a bit thin...
    25 replies | 571 view(s)
  • leebuilder's Avatar
    12-28-2017, 02:07 PM
    Your welcome. Good luck ! Ralph
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-28-2017, 09:15 AM
    Morning, that's the front sling swivel exactly. I can only assume they built in large numbers. Issue to where and how many I have no idea. Before our now debunked gun registry they were piles of them around, now not so many. You could get one for...
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-27-2017, 12:04 AM
    Not aware of PH p17 or 14s, seen a few BSA p14 &17s as well as churchil branded ones and bubbas. i can only assume there are more. there were PH modifed no1s sold by sears up here. They have no rear hand guard and the cut outs were filled in with...
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-26-2017, 10:44 PM
    Bombers they were issued as survival rifles to the RCAF planes after ww2. Some were modifed surplus, some were from parker hale and there were the EAL rifles purpose built, EAL rifles fall into two catagorys military and civilian (each catagory has...
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-26-2017, 05:22 PM
    Higgens, nurmrich/e gunparts had cut off forends at one time, now i do not know. Maybe try Brian Dick longarms as well. Jmax I know of the grooves for the hood, but i havent found any PH branded ones that fit close to it. I managed to get one off...
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-25-2017, 09:08 PM
    That's outstanding. Good luck!
    44 replies | 2816 view(s)
  • leebuilder's Avatar
    12-25-2017, 01:36 PM
    Hi. Good find getting a LB "bomber". I think there are no sight hoods made for the PH front sights, belive me i have looked and other PH hoods will not fit. Caution about the crown seen many that look very good but under closer inspection they are...
    28 replies | 951 view(s)
  • leebuilder's Avatar
    12-23-2017, 08:23 AM
    Got the NOE 314 115 rg2 mold last week and managed to load up a few with lube and PCED a few. Best so far PCed and sized to .314 under 3.5 gr of red dot in an old savage two groove no4 mk1☆ Even found two heads the hollow point was undamaged...
    14 replies | 2027 view(s)
  • leebuilder's Avatar
    12-18-2017, 10:13 PM
    My 160 2r drops .311 I have 2, 185 1r both drop .312 All are WW. Be well
    3 replies | 321 view(s)
No More Results
About leebuilder

Basic Information

Age
49
About leebuilder
Biography:
Retired navy articifer. Been collecting rifles since i was 19. I am a machinist. Have loved the silver stream since i was eight when i got a tin melting set
Location:
Nova Scotia
Interests:
rifle building and restoration
Occupation:
layed off marine mecanic

Signature


When you read the fine print you get an education
when you ignore the fine print you get experience

Statistics


Total Posts
Total Posts
860
Posts Per Day
0.76
Albums
Total Albums
1
Total Photos
0
General Information
Last Activity
Today 11:08 AM
Join Date
12-13-2014
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check