MidSouth Shooters SupplyGraf & SonsRepackboxInline Fabrication
WidenersStainLess Steel MediaRotoMetals2Lee Precision
Titan Reloading
  • Pavogrande's Avatar
    11-13-2018, 01:46 PM
    I have a williams fp that is for the 87 so they were available - It does require drilled/tapped holes though -- It looks like a fit for my old savage or mossberg as well - perhaps any round receiver --
    1 replies | 185 view(s)
  • Pavogrande's Avatar
    11-13-2018, 12:39 PM
    I have a set of rcbs 30/30 ai dies -- older but unused - pm me if of interest --
    45 replies | 3078 view(s)
  • Pavogrande's Avatar
    11-07-2018, 08:10 PM
    The # 7 handle adapter (45 colt) is required for the 45acp and ar rather than the #2 (06 etc) This is because the short case expands beyond body diameter and it hangs up in the #2 - My set has #14 primer for the 45ar - My 45/70 uses #17 primer
    10 replies | 414 view(s)
  • Pavogrande's Avatar
    11-02-2018, 04:54 PM
    Ken there is a nice range in Midlothian if you are in the dallas area -
    5 replies | 437 view(s)
  • Pavogrande's Avatar
    11-02-2018, 04:48 PM
    I have been considering one of those as well -- Outdoor shooting is not as convenient for me here in georgia, more outdoor ranges and of course BLM land in calif. I just bought a new ruger PC 9 carbine for indoor shooting so the gsg 1911 will...
    4 replies | 320 view(s)
  • Pavogrande's Avatar
    10-31-2018, 06:05 PM
    BR thanks for your viewpoint --- I expect you are correct most folk never heard of them. - I expect modern dies probably do a better job, certainly faster -- I have some 22 cups perhaps i will make a push rod and give the dies a try -- Must...
    11 replies | 810 view(s)
  • Pavogrande's Avatar
    10-29-2018, 10:31 PM
    My database says I have 23 R P cases -- It also says I have rcbs 17/222mag sizer -- Lord knows from where or when -- I will verify the cases tomorrow --
    1 replies | 127 view(s)
  • Pavogrande's Avatar
    10-29-2018, 10:09 PM
    Quite a co-incidence - I am missing the same part -- Just going to make one using brass stock -- It is not a precision part -- gl with search
    5 replies | 302 view(s)
  • Pavogrande's Avatar
    10-25-2018, 06:21 PM
    Just to add to the confusion my 6.5 jap die is 1.612 long - My die is an MR die and is marked 6.5jap not 137 - your dies MR or CMR's george now in georgia
    7 replies | 387 view(s)
  • Pavogrande's Avatar
    10-25-2018, 06:07 PM
    I had a couple sets of those dies -- the 7/8 FL sizer was threaded from the "top" and screwed into the press from the bottom --
    9 replies | 844 view(s)
  • Pavogrande's Avatar
    10-24-2018, 11:18 AM
    skeettx -- perhaps you could post a photo of your dies as I am unable to post any -
    11 replies | 810 view(s)
  • Pavogrande's Avatar
    10-24-2018, 09:12 AM
    The die in your fingers is half of a Herters primer pocket swage -- the other half is a swage button that fits into a shellholder -- for 06 and 308 size cases -- The 90 degree bent rod with clips is a holding fixture for welding bolt handles. my...
    3 replies | 595 view(s)
  • Pavogrande's Avatar
    10-23-2018, 10:43 PM
    Ken for some reason i can not get the photo - manage file - to work - tried this afternoon and just now - Die body is two piece -- lower section threads into press - upper section - nose forming - is threaded to lower section with a interrupted...
    11 replies | 810 view(s)
  • Pavogrande's Avatar
    10-23-2018, 12:40 PM
    I have two rcbs bullet swage dies 22 and 25 calibers - These are some of the first dies Fred made, perhaps wwii or soon after - They are two piece, interuptred thread and useable in a standard 7/8" threaded press - Any one have feel for their...
    11 replies | 810 view(s)
  • Pavogrande's Avatar
    10-23-2018, 12:11 PM
    I have two rcbs bullet swage dies 22 and 25 calibers - These are some of the first dies Fred made, perhaps wwii or soon after - They are two piece, interuptred thread and useable in a standard 7/8" threaded press - They are a real machinists...
    0 replies | 245 view(s)
  • Pavogrande's Avatar
    10-23-2018, 11:50 AM
    I too feared the big dumpster -- My daughter and son in law have promised to find a home for my stuff when that time comes - At my age most any time :-)
    34 replies | 4420 view(s)
  • Pavogrande's Avatar
    10-23-2018, 11:18 AM
    I have 3 years of these in binders -- I think the binders cost more than the mags -- Really liked graham burnside on cartridges -- The newsprint is getting a mite brittle -- Probably should pass them on --
    8 replies | 1364 view(s)
No More Results
About Pavogrande

Basic Information

About Pavogrande
Biography:
usn 1953-57 -- fmc corp, mechanic to manager of facilites - retired after 35 years
Location:
Dacula Ga formerly san josie calif
Occupation:
Retired - Machine builder/facilities manager FMC Corp

Statistics


Total Posts
Total Posts
585
Posts Per Day
0.14
General Information
Last Activity
Yesterday 10:22 PM
Join Date
10-16-2007
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check