MidSouth Shooters SupplyADvertise hereWidenersLee Precision
RotoMetals2Inline FabricationTitan Reloading

Tab Content
  • jednorris's Avatar
    10-10-2019, 09:06 AM
    It was an older sight and the index marks at the base of the sight were too light to see clearly. I saw Lee's information, but it still did not tell direction of rotation. I have my answer now and thanks to everyone.
    5 replies | 454 view(s)
  • jednorris's Avatar
    10-09-2019, 04:00 PM
    I just got a Lee Shaver top of the line sight and am anxious to sight it in. To save ammo and frustration will somebody tell me how to adjust windage. Looking at the right side, does rolling the windage knob clockwise move my P.O.I. right ?. I...
    5 replies | 454 view(s)
  • jednorris's Avatar
    10-03-2019, 07:22 PM
    I purchased a custom built .40/65 and it does not have a very good rear tang sight. The mounting holes for the base of the sight that is on there looks to be 1.550" apart. I would like to buy a mid range sight that I can just screw back on without...
    10 replies | 359 view(s)
  • jednorris's Avatar
    10-01-2019, 07:36 PM
    I have a top ladle lead pot. I use beeswax as I was told that paraffin was not as good. I hear people talking about fluxing with pine sawdust, but I was told that the only purpose for that was to retain heat over the top of bottom pours. What does...
    28 replies | 716 view(s)
  • jednorris's Avatar
    10-01-2019, 07:30 PM
    Gunbroker offers a place to rate the sellers profile. You can do a writeup and describe your problems and dis satisfaction. Checking the sellers history can help or kill a sale.
    24 replies | 1554 view(s)
  • jednorris's Avatar
    09-24-2019, 07:43 PM
    Country Gent and Bazoo hit the nail on the head, I had the plate too tight to allow air to escape. I adjusted it until I got good bullets and then hit the ground running. This sight and the people on it have been a blessing.
    19 replies | 530 view(s)
  • jednorris's Avatar
    09-21-2019, 04:09 PM
    I loosened the screw a little and it seems better. I think I have it adjusted just about right but every once in a while I get one that does not have a squared base. I think I am causing an air pocket the way I am pouring and am working on that.
    19 replies | 530 view(s)
  • jednorris's Avatar
    09-20-2019, 04:27 PM
    I found the set screw and have the screw snugged down. Now I have a different problem. The bases of my bullets are beginning to get rounded rather than squared off and I cannot find what I am doing wrong.
    19 replies | 530 view(s)
  • jednorris's Avatar
    09-20-2019, 12:05 AM
    When I am casting bullets I sometimes find the screw that keeps the shear plate on top of my mold loosens. I think this might cause weight variations as I never seem to keep my bullet weights as consistent as most people. Is there something I can...
    19 replies | 530 view(s)
No More Results
About jednorris

Basic Information

Statistics


Total Posts
Total Posts
88
Posts Per Day
0.05
General Information
Last Activity
Yesterday 11:23 PM
Join Date
07-22-2014
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check