MidSouth Shooters SupplyInline FabricationLee PrecisionGraf & Sons
ADvertise hereRotoMetals2Titan ReloadingStainLess Steel Media

Tab Content
  • LAGS's Avatar
    02-19-2018, 08:50 PM
    Thank you for the post. It gives me some ideas on what to do with several I J, H A and H R receivers that I have acquired over the years. I was sleeving the barrels and cylinders to a smaller caliber if the gun was not in serviceable condition,...
    7 replies | 215 view(s)
  • LAGS's Avatar
    02-18-2018, 08:38 PM
    I don't say I Built A Mauser Rifle. In most cases, I say, I Built this rifle on a Mauser Action. I will take credit for what I Built, but unless I built the action, how can that figure into my skills. But To me, Putting a new Barrel on a Mauser...
    41 replies | 1061 view(s)
  • LAGS's Avatar
    02-17-2018, 11:17 AM
    Can you not just Fabricate something for yourself out of wood. It really isnt that hard. And if you are doing only one project, it makes no sense to me to BUY some Fancy jig to do One simple job. I'm sorry. But too many times I see people rely...
    2 replies | 152 view(s)
  • LAGS's Avatar
    02-13-2018, 08:28 PM
    @ KCSO I did the spring thing on the friction Piece before. And I did the same modification on the bolt sleeve to make the installation of the spring and plunger or the straight Nylon Piece easier to install. I filed a small notch in the hole or...
    15 replies | 367 view(s)
  • LAGS's Avatar
    02-13-2018, 07:24 PM
    One thing the O P posted. He said he put the safety in the halfway position , between Safe and fire , then pulled the trigger. These are TWO position Safeties. There is No Cheating. In the middle position, the cocking piece is sitting on the...
    15 replies | 367 view(s)
  • LAGS's Avatar
    02-13-2018, 07:18 PM
    You can cut your shotgun Barrel off as short as you want it, without a permit. As long as you dont mind having a wife named Bubba for the next ten years.
    34 replies | 1019 view(s)
  • LAGS's Avatar
    02-12-2018, 11:18 PM
    If you put the safety in the Safe position, then pull the trigger, the cam on the safety should hold the cocking piece far enough to the rear to allow the sear to come back up and re- engage. No different than the original safety One way to check...
    15 replies | 367 view(s)
  • zubrato's Avatar
    02-01-2018, 07:09 PM
    I ice water quench my 50/50 pure/coww + splash of tin for my pistol boolits. Iím not a bench rest shooter, and I donít caliper measure my groups. I shoot for practical accuracy, and Iíve never had an issue other than being extra careful for...
    24 replies | 734 view(s)
  • LAGS's Avatar
    01-28-2018, 09:07 PM
    Money has not been a deciding factor in my book, it is the time . The time waiting for the Correct part, then to find out that is Not Correct as you thought. But the whole scope mount I made took me about two hours, and about $10.00 at most in...
    10 replies | 340 view(s)
  • LAGS's Avatar
    01-28-2018, 08:57 PM
    The Timney trigger is GREAT. That is, if you want to modify your stock. That is the question. You want an original rifle to shoot better, But you do not want to modify your rifle to fit an aftermarket trigger to make it shoot better. A little...
    8 replies | 349 view(s)
  • LAGS's Avatar
    01-28-2018, 04:54 PM
    I had a situation happen years ago that was very similar. I was able to use a Patch removal Jag to get the old brush out. Destroyed the brush, but at that point I didn't care.
    41 replies | 1869 view(s)
  • LAGS's Avatar
    01-28-2018, 03:00 PM
    I just got tired of trying to keep everything Original. I would rather have something Functional, and be out shooting, rather than wait for some Part that is not as good or what i really want. But then I do my own work out of scrap I have laying...
    10 replies | 340 view(s)
  • LAGS's Avatar
    01-25-2018, 08:35 PM
    I just made my own mount
    10 replies | 340 view(s)
No More Results
About LAGS

Basic Information

About LAGS
Location:
Arizona
Interests:
Hunting , Gunsmithing, Reloading
Occupation:
Construction Superintendent

Statistics


Total Posts
Total Posts
1,576
Posts Per Day
1.19
General Information
Last Activity
Today 02:09 AM
Join Date
07-16-2014
Referrals
0

3 Friends

  1. armoredman armoredman is offline

    Boolit Master

    armoredman
  2. UBER7MM UBER7MM is offline

    Boolit Master

    UBER7MM
  3. zubrato zubrato is online now

    Boolit Master

    zubrato
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check