MidSouth Shooters SupplyInline FabricationLee PrecisionTitan Reloading
ADvertise hereWidenersRotoMetals2Repackbox

Tab Content
  • JMax's Avatar
    Today, 04:06 PM
    JMax replied to a thread Ruger PC 9mm Carbine in Cast Boolits
    4 gr TiteGroup with a powder coat Lee 120 TC, I pick clay pigeons and pieces at 100 yards, I use a 3X scope.
    12 replies | 155 view(s)
  • JMax's Avatar
    06-29-2020, 03:17 PM
    I have been using Win primers exclusively For decades and finished firing up a thousand 38 loads without any misfires. I use WLR, WSR, WSP and WLP Without incident.
    13 replies | 366 view(s)
  • JMax's Avatar
    06-25-2020, 11:32 AM
    I have a 550 and an 550B. Both seat primers below case base but if the shell plate has excessive wobble (Loose bolt) then primer seating can be problematic. Push the press arm all the way to the rear and look for primer punch protrusion above the...
    6 replies | 241 view(s)
  • JMax's Avatar
    06-14-2020, 04:13 PM
    I am an old LEO Smith armorer plus built a number of match revolvers. Re-barreled my 1917 with a 6 1/2” 1955 target barrel, adjustable rear sight and made it into a fun shooter. Things that I learned are that lower track parts including trigger,...
    22 replies | 1052 view(s)
  • JMax's Avatar
    06-14-2020, 03:55 PM
    I use the NOE equivalent 299314 sized to .311 for my Krag made in 1902, an 03 made in 1934 and No4 MkI 5 groove made in 1944 sized to .314. My load is 17 gr 2400 when I do my job the rifles they always do theirs.
    8 replies | 324 view(s)
  • JMax's Avatar
    06-06-2020, 08:42 PM
    JMax replied to a thread Worth the effort? in Cast Boolits
    Be careful as you will experience RPM fatigue. I fought the battle with my Norwegian Krag in 6.55x55 and learned that I was limited to 1350 ft/sec.
    2 replies | 237 view(s)
  • JMax's Avatar
    06-04-2020, 12:04 PM
    Remember it’s custom loaded:bigsmyl2:
    16 replies | 1659 view(s)
  • JMax's Avatar
    06-02-2020, 04:37 PM
    JMax replied to a thread I'm done too... in Cast Boolits
    I use the Lee TC120 sized to .356" powder coated with HF Red and now Yellow Gasp as it shoots better in my Ruger PC at 50 and 100 yards. My Glocks with factory barrels liked .357" better but my volume 9mm is Hoover my Ruger PC. the load is 4 gr of...
    29 replies | 3253 view(s)
No More Results
About JMax

Basic Information

About JMax
Been casting for a very long time
Competitive shooting, reloading


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 04:06 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check