StainLess Steel MediaLee PrecisionGraf & SonsTitan Reloading
RotoMetals2MidSouth Shooters SupplyADvertise hereInline Fabrication

Tab Content
  • wmitty's Avatar
    04-15-2018, 11:55 PM
    I should have mentioned that I was patching both bore riding nose and driving bands/ gas check shank. I've loaded five rds each of 40 gr 4895, 41 gr, 42 gr and 43 gr for my M700 .30-06 and will try 'em this week. Not sure of this sentence structure;...
    4 replies | 109 view(s)
  • wmitty's Avatar
    04-14-2018, 07:44 PM
    I'm going against what p dawg shooter and others have posted on using a boolit for paper patching by not lapping the bore riding portion to same dia. as driving bands. Using a RCBS .30- 180 - FN and sizing it to .3032" while the nose varies from...
    4 replies | 109 view(s)
  • wmitty's Avatar
    04-05-2018, 08:58 PM
    Which boolit and what was your load?
    2 replies | 146 view(s)
  • wmitty's Avatar
    04-04-2018, 11:59 PM
    wmitty replied to a thread Savage 775 in Casting for Shotguns
    Savage is nicer than the Rem M 11 in my opinion. Browning design w/o the magazine cutoff.
    4 replies | 230 view(s)
  • wmitty's Avatar
    04-02-2018, 06:10 PM
    You will be going backwards by reducing the acute shoulder angle and increasing body taper. I would use an rcbs file/trim die and size down in steps to help prevent collapsed cases. Good luck; hadn’t heard of this before.
    5 replies | 150 view(s)
  • wmitty's Avatar
    04-01-2018, 02:21 PM
    Rebarreled my M93 and I shortened the size die to allow case to fit the chamber. I liked the chamber as it was cut and don't use factory ammunition anyway so saved the rental on a finish reamer.
    29 replies | 738 view(s)
  • wmitty's Avatar
    03-27-2018, 03:21 AM
    Planning to meet you soon, Mr Kort.
    28 replies | 1272 view(s)
  • wmitty's Avatar
    03-26-2018, 11:52 PM
    HABCAN I think you have some folks sitting and shaking their heads. What you are doing isn’t supposed to work; at least according to the “ standard operating procedures “ of paper patching. I have had some success following the s.o.ps but I’m...
    27 replies | 2231 view(s)
  • wmitty's Avatar
    03-26-2018, 11:21 PM
    Are there any barrel suppliers offering twist rates slower than 1/12 without the barrel being special ordered/ custom made? Not sure how to ask this question but it seems the slowest twist commonly available for the rem 700 is 1/12 and e.r. Shaw...
    7 replies | 380 view(s)
  • wmitty's Avatar
    03-26-2018, 10:51 PM
    wmitty replied to a thread stupid idea... .22 WMR in Cast Boolits
    Make sure you wear a face shield if you mess with the priming compound
    21 replies | 670 view(s)
  • wmitty's Avatar
    03-26-2018, 09:12 PM
    wmitty replied to a thread Casting questions in Cast Boolits
    Welcome aboard! I have to agree with Yodogs. The pc is causing the oversize boolit. Tumble lube those and they will work great. Ben's LL is super!
    30 replies | 756 view(s)
  • wmitty's Avatar
    03-25-2018, 09:35 PM
    Friends in Houston talked me into getting on a deer lease with 'em out near Fredricksburg; west of Austin. I asked them what cartridge they were using in their rifles and they said .222 Rem. I laughed until I actually saw the size of the deer. They...
    24 replies | 1428 view(s)
  • wmitty's Avatar
    03-25-2018, 09:26 PM
    The 788 .30-30 has a bore dia. of .302" (as best I can determine without a set of pin gages) so should be o.k. with .3032" boolits. Groove is right at .309" so I am trying tracing paper and am not used to not sizing the wrapped slug. I'm going to...
    4 replies | 224 view(s)
  • wmitty's Avatar
    03-23-2018, 10:05 PM
    Ran out of .30 gas checks and decided to go with paper patching for a while. The 311466 isn't a bore rider and went thru the Lee push thru .303" die with no apparent unwanted distortion. Will this design work for pping? I have been looking for a...
    4 replies | 224 view(s)
No More Results
About wmitty

Basic Information

Date of Birth
February 1, 1953 (65)
About wmitty
Biography:
native texan, A & M grad.,
Location:
sulphur springs, Tx
Interests:
hunting, shooting, weight lifting, reading, trying to escape to New Mexico
Occupation:
construction inspector with TxDoT

Signature


There are only to kinds of men:

1. Those who know Jesus Christ is both Creator and Sovereign Lord.

2. Those fixin' to know...

Statistics


Total Posts
Total Posts
875
Posts Per Day
0.18
General Information
Last Activity
Today 04:28 AM
Join Date
04-07-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check