StainLess Steel MediaInline FabricationWidenersRotoMetals2
Graf & SonsRepackbox

Tab Content
  • wmitty's Avatar
    12-13-2018, 07:11 PM
    Isn't the sear spring also the trigger return spring on the 788's factory trigger? Seems like I remember a modification where that spring is shortened and a separate return spring and screw is installed.
    21 replies | 568 view(s)
  • wmitty's Avatar
    12-11-2018, 11:59 PM
    Thanks for the input, gentlemen. I think I'll be looking for a 1-14" twist barrel.
    12 replies | 379 view(s)
  • wmitty's Avatar
    12-10-2018, 09:45 PM
    Kreiger has a .30 caliber blank with a 1-17" twist rate. Asking for opinions; would the 311466 be stabilized at such a slow twist rate? Looking to build a dedicated cast boolit shooter in .30-06 and don't want to go to an extreme twist if it will be...
    12 replies | 379 view(s)
  • wmitty's Avatar
    12-08-2018, 04:04 PM
    I thought caliber was a designation of the bore and groove diameter of a rifled barrel. I thought cartridge was the designation of the case containing a specific volume of propellant; and could be of the same caliber or smaller or larger caliber. I...
    101 replies | 3518 view(s)
  • wmitty's Avatar
    12-08-2018, 04:45 AM
    White rabbit I have not tried WC-872 but it’s only a little slower than 860. I’d give it a try; especially if you go with a heavier boolit. I checked records & showed 2300 FPS with the Lyman (paper patched) and a case full of 860.
    23 replies | 521 view(s)
  • wmitty's Avatar
    12-04-2018, 03:36 PM
    I have the RCBS 37-250-FN (gas check) and the Lyman 378674 (plain base). The RCBS will shoot into 4" at two hundred yards. Have not got to shoot that distance with the Lyman. Unless you are independently wealthy, you'll need to get some WC 860 from...
    23 replies | 521 view(s)
  • wmitty's Avatar
    12-01-2018, 05:56 PM
    Using range pickup brass to form into .222 Rem and learned the hard way about weight (case volume) variation. Iím now sorting cases by weight and loading a batch of similar weight cases (one grain spread) and am wondering if this is too...
    2 replies | 175 view(s)
  • wmitty's Avatar
    11-23-2018, 10:33 PM
    Until you shoot paper patched boolits thru a rifle it’s difficult to believe the polishing effect it has on a bore. 303guy has mentioned a number of times the Enfield barrels he has brought back from the dead. Rooskie might work too.
    42 replies | 1782 view(s)
  • wmitty's Avatar
    11-20-2018, 12:42 PM
    There is currently a .30 cal throating reamer on flea-bay. In looking it over appears the end of the reamer is supported by the bore diameter surface and would be unsupported by a bore several thousandths larger (say a Marlin 336 microgroove). Am I...
    3 replies | 234 view(s)
  • wmitty's Avatar
    11-18-2018, 04:43 PM
    wmitty replied to a thread Gato Feo #1 in Boolit Lube !
    Ugly cat lube?
    8 replies | 607 view(s)
No More Results
About wmitty

Basic Information

Date of Birth
February 1, 1953 (65)
About wmitty
Biography:
native texan, A & M grad.,
Location:
sulphur springs, Tx
Interests:
hunting, shooting, weight lifting, reading, trying to escape to New Mexico
Occupation:
construction inspector with TxDoT

Signature


There are only two kinds of men:

1. Those who know Jesus Christ is both Creator and Sovereign Lord.

2. Those about to learn that Jesus Christ is both Creator and Sovereign Lord.

Statistics


Total Posts
Total Posts
922
Posts Per Day
0.18
General Information
Last Activity
Today 01:45 AM
Join Date
04-07-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check