Graf & SonsTitan ReloadingMidSouth Shooters SupplyInline Fabrication
RotoMetals2Lee PrecisionADvertise hereStainLess Steel Media

Donate Now Goal amount for this year: 6000 USD, Received: 4840 USD (81%)
We have reached our goal! Thanks to all who donated! I will be updating the donation bar in the next few days!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • wmitty's Avatar
    07-28-2018, 09:42 PM
    I'd melt it all down and see what hardness you have. Probably will be pretty soft so high velocity is probably gonna require adding wheelweights or another source of antimony. Heat it slowly and be real suspicious of anything that doesn't melt after...
    17 replies | 613 view(s)
  • wmitty's Avatar
    07-24-2018, 10:34 PM
    Iíve this boolit for a m 93 I rebarreled (7x57) but I have not tried hunting with it. I have an old rcbs 168 grain that I want to try on the local piggies; but like your experience it sets very far down in the case. Gas check nearly sits on the...
    13 replies | 480 view(s)
  • wmitty's Avatar
    07-23-2018, 03:20 AM
    Not sure where to post this but could someone elaborate on what effect (if any) enlarging the size of the flashhole has on ignition of powder charge. It would seem that the diameter could be increased somewhat and still allow the anvil within the...
    12 replies | 551 view(s)
  • wmitty's Avatar
    07-22-2018, 02:39 PM
    Short throat - which boolit are you going with?
    10 replies | 278 view(s)
  • wmitty's Avatar
    07-21-2018, 05:29 PM
    wmitty replied to a thread Sabot for 308 Shoots 223 in Swaging
    I bought a box of .30-06 Accelerator s just out of curiosity and the factory bullets shot about 1.5 moa. I used an inertia puller and checked the bullets - they were flatbase with an unusually sharp radius. I replaced a few factory bullets with some...
    16 replies | 576 view(s)
No More Results
About wmitty

Basic Information

Date of Birth
February 1, 1953 (65)
About wmitty
Biography:
native texan, A & M grad.,
Location:
sulphur springs, Tx
Interests:
hunting, shooting, weight lifting, reading, trying to escape to New Mexico
Occupation:
construction inspector with TxDoT

Signature


There are only two kinds of men:

1. Those who know Jesus Christ is both Creator and Sovereign Lord.

2. Those about to learn that Jesus Christ is both Creator and Sovereign Lord.

Statistics


Total Posts
Total Posts
899
Posts Per Day
0.18
General Information
Last Activity
08-10-2018 08:56 PM
Join Date
04-07-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check