Lee PrecisionGraf & SonsInline FabricationMidSouth Shooters Supply
RotoMetals2ADvertise hereStainLess Steel MediaTitan Reloading

Donate Now Goal amount for this year: 6000 USD, Received: 4840 USD (81%)
We have reached our goal! Thanks to all who donated! I will be updating the donation bar in the next few days!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


  • bstone5's Avatar
    Today, 01:26 AM
    Shoot 14 grains of Trail Boss in a Handi-Rifle chambered in 45-70. Shoots very accurately and does not kick too bad. Have shot several hundred rounds and still using the original 50 cases. Anneal every 100 shots. A lot of fun with a set of...
    15 replies | 258 view(s)
  • bstone5's Avatar
    Today, 01:08 AM
    Chore Boy Pure Copper scrubbers are commonly used by dope smokers. A convince store by me keeps them in stock with the cigarette rolling paper.
    5 replies | 108 view(s)
  • bstone5's Avatar
    Yesterday, 12:45 AM
    bstone5 replied to a thread 25-06' what to do ? in Cast Boolits
    Shot a deer at 1200 yards with a 25-06. Put the rifle together for my son when he was 14 years old, he is now 42. The rifle has shot well all of the time and now has less than 200 rounds fired thru the barrel. A Ruger bolt action, new barrel and...
    15 replies | 213 view(s)
  • bstone5's Avatar
    08-14-2018, 11:58 PM
    I size to. .357 and use the same bullets in 9 mm guns and 38 Special guns. All are powder coated to keep lead out of the barrels. Have shot thousands of the powder coated bullets sized to .357 without any problems.
    13 replies | 208 view(s)
  • bstone5's Avatar
    08-13-2018, 11:20 PM
    I use 444 Marlin brass for reloads in my S&W Govonor hand gun. I have shot the reloaded brass several times with out needing to size the 444 Marlin brass. There is a lot of info on this site for loading the 444 Marlin brass as a shot she'll. I...
    20 replies | 463 view(s)
  • bstone5's Avatar
    08-11-2018, 01:05 AM
    Have a Handi-Rifle in 45-70 shoot it a lot with light bullets and Trail Boss powder. The load does not kick much and is accurate out to 100 yards. Have Williams peep sights on the rifle, the rear sight has a lot of adjustment to get on target at...
    26 replies | 612 view(s)
  • bstone5's Avatar
    08-09-2018, 11:34 PM
    Retired at the age of 70 two years ago. Worked in the offshore drilling industry for a very long time. Over the years drilled offshore all over the world. Spent time in the North Sea, South America, the Far East, Africa and some other not so...
    44 replies | 1007 view(s)
  • bstone5's Avatar
    08-07-2018, 01:25 AM
    Fire lapping sometimes work but as suggested earlier paper patched bullets might be better choice for a first try. I have manually hand lapped a lot of barrels over the years but I ruined a few barrels in the process of learning the process.
    26 replies | 722 view(s)
  • bstone5's Avatar
    08-07-2018, 01:13 AM
    bstone5 replied to a thread Annealing brass? in Single Shot Guns
    Anneal the 45-70 brass after three firings, use Star Line brass and shoot cast lead powder coated with a home made gas check bullets using Trail Boss powder. The rifle is a H&R Handi rifle that is light in weight. Have used the same brass for...
    26 replies | 703 view(s)
  • bstone5's Avatar
    08-07-2018, 01:05 AM
    Use a 117 grain cast bullet that is powder coated and a home made gas check is installed on the plain base cast bullet. Use VV-N-10 most of the time but have used H-110 when the VV powder was not available. No leading and gun barrel very clean. ...
    28 replies | 1096 view(s)
  • bstone5's Avatar
    08-07-2018, 12:57 AM
    I stand them up since I use the electronic spray gun to apply the powder coat. This works best for me since I coat several thousand bullets over a few days.
    20 replies | 619 view(s)
  • bstone5's Avatar
    08-04-2018, 10:40 PM
    I flux with the flux from Magma Engineering on my Master Caster. I used saw dust in the past but found some of the carbon would plug the outlet on the Master Caster pot. Ordered the flux from the manufacture of the Master Caster and the lead...
    50 replies | 1586 view(s)
No More Results
About Tom_Highway

Basic Information

Statistics


Total Posts
Total Posts
30
Posts Per Day
0.02
General Information
Last Activity
06-12-2018 07:52 PM
Join Date
04-11-2014
Referrals
0

2 Friends

  1. bstone5 bstone5 is offline

    Boolit Master

    bstone5
  2. Guardian Guardian is offline

    May Liberty Increase!

    Guardian
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check