RepackboxLee PrecisionTitan ReloadingInline Fabrication
MidSouth Shooters SupplyWidenersADvertise hereRotoMetals2

Tab Content
  • tazman's Avatar
    Yesterday, 04:01 PM
    Data for WST is available online at the Hodgdon data site.
    16 replies | 251 view(s)
  • tazman's Avatar
    Yesterday, 12:33 PM
    I use the Lyman 452374 for full power loads and the Lee 452-200-rf for light loads. Other boolits are the H&G 68 clone from LEE and the Lyman 453460. I use several different powders depending on what I am trying to do specifically. Bullseye, WST,...
    16 replies | 251 view(s)
  • leadhead 500's Avatar
    03-28-2020, 10:42 PM
    Most people hear about heavy bullets in 357 magnum and think no way possible, the old 38 special was loaded with a 200 grain lead! There is some good info from Glen Fryxell on the web about the Lyman 358627
    14 replies | 419 view(s)
  • leadhead 500's Avatar
    03-28-2020, 10:05 PM
    The Lyman 358627 or the Noe clone weighs in at 215 grains and is a outstanding heavyweight in the 357 magnum. My S&W 686 with a 8 3/8” loaded with Winchester 296 or H-110 is very accurate
    14 replies | 419 view(s)
  • tazman's Avatar
    03-28-2020, 04:59 AM
    That should be an excellent combination. It is exactly what I have and it performs well. For a light load, use the Lee 358-125-RF with around 3.0 grains of Bullsye or Tightgroup in a 38 special case. In my gun, this shoots to the same point of...
    35 replies | 641 view(s)
  • tazman's Avatar
    03-27-2020, 01:30 PM
    I have never used Shooters World powders. My Lee Pro Auto Disk measures don't leak with the Winchester, Hodgdon, IMR, and Alliant powders I do use. I have these measures on turrets for my Lee Classic Cast turret press. I have six of them and they...
    20 replies | 372 view(s)
  • tazman's Avatar
    03-26-2020, 06:15 PM
    In the vast majority of my accuracy testing, the only way I can tell differences in accuracy is from a rest. Even when the groups from rest are one half to one inch different at 25 yards, my offhand shooting doesn't show any difference in group...
    27 replies | 714 view(s)
  • tazman's Avatar
    03-26-2020, 10:17 AM
    I shoot 99% 38special. Anywhere from super light plinking/practice rounds to full power loads. The only full magnum loads I fire in mine is to test for point of impact and accuracy for when I would need to use them.
    35 replies | 641 view(s)
  • tazman's Avatar
    03-25-2020, 08:50 PM
    I have owned several different 686 revolvers. They all shot well. The one I now own is a 686+ with the lock and the ECM barrel. It shoots just as well as the others with both jacketed and cast. I,too, used to look down on the new guns with the lock...
    35 replies | 641 view(s)
  • tazman's Avatar
    03-25-2020, 08:44 PM
    If you see your sights better without prescription glasses, do what I do and just use regular safety glasses that have no prescription. I found I could see my sights clearly and the target well enough to vastly improve my groups with a handgun and...
    28 replies | 967 view(s)
  • tazman's Avatar
    03-25-2020, 08:35 PM
    The need for a thermometer depends greatly on how precise you want to be. Are you looking for the ultimate in cast accuracy? Then get a thermometer as well as some other testing goodies, such as hardness tester and even a way to test your alloy. If...
    11 replies | 320 view(s)
  • tazman's Avatar
    03-25-2020, 06:03 PM
    Earmuffs are limited in the amount of noise reduction they can provide as are ear plugs. When I am shooting, I use both. I want to save what hearing I have left after 40+ years at a noisy factory. If I know the noise level is going to be less(22...
    8 replies | 224 view(s)
  • leadhead 500's Avatar
    03-25-2020, 05:10 PM
    The Rcbs thermometer is outstanding! The lead pots will vary on temperature and every Mould will vary on what temperature it cast the best at.
    11 replies | 320 view(s)
  • rmcc's Avatar
    03-23-2020, 09:41 PM
    rmcc replied to a thread byf 43. in Military Rifles
    Was made by Mauser in 43
    3 replies | 158 view(s)
  • tazman's Avatar
    03-20-2020, 06:37 PM
    There was a time, not so long ago, that the 222 was considered one of the most inherently accurate cartridges ever made. Lots of new stuff out there now making the same claim. I suspect the new barrels and better bullets have something to do with...
    34 replies | 1127 view(s)
  • tazman's Avatar
    03-20-2020, 05:13 PM
    tazman replied to a thread Accurate bullet BC in Cast Boolits
    Ballistic coefficients for Lee and NOE are available online at their sites. If a mold doesn't have a BC listed, I find the closest boolit shape and weight from one of these two and use that. Any minor differences in BC for a pistol boolit isn't...
    9 replies | 296 view(s)
More Activity
About tazman

Basic Information

About tazman
Long time hunter and fisherman. Recently re-entered reloading and casting for fun and experience after 15 years away.
west central Illinois
hunting fishing archery photography
recently retired


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 11:39 PM
Join Date

5 Friends

  1. .5mv^2 .5mv^2 is offline

    Boolit Buddy

  2. Gumby102b Gumby102b is offline

    Boolit Mold

  3. leadhead 500 leadhead 500 is offline

    Boolit Buddy

    leadhead 500
  4. ProudOkie ProudOkie is offline

    Boolit Bub

  5. rmcc rmcc is offline

    Boolit Master

Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check