WidenersRepackboxStainLess Steel MediaRotoMetals2
Graf & SonsInline FabricationMidSouth Shooters SupplyLee Precision
Titan Reloading
  • Handloader109's Avatar
    Yesterday, 11:02 AM
    Handloader109 replied to a thread Digging out in Our Town
    I had a big 30x30 metal building back in MS stuffed with stuff. Woodworking, tools, all sorts of stuff. Vandals took a couple of 3 thousand out of it, air compressor, some saws, mainly large stuff they could sell for decent $ at the pawnshops. ...
    30 replies | 635 view(s)
  • Handloader109's Avatar
    10-19-2018, 12:01 PM
    Just for note, I use 10-11 grains of H110/296 in my 22TCM. Bottlenecked .223 cut off. Works fine, LOUD out of the 1911/2011 with a big flash. Appears to be identical to the OEM powder.
    51 replies | 3901 view(s)
  • Handloader109's Avatar
    10-19-2018, 10:09 AM
    It's FRIDAY! Bump
    24 replies | 1007 view(s)
  • Handloader109's Avatar
    10-19-2018, 08:22 AM
    Handloader109 replied to a thread table saw problems in Our Town
    I'd stop trying to get by with junk saws. You'd be better using a handheld circular saw... Ohio forge is a junk harbor freight type brand. Forget parts. You wont find any. Get an older craftsman next time, bulletproof, and most motors are cheap...
    21 replies | 568 view(s)
  • Handloader109's Avatar
    10-19-2018, 08:16 AM
    Desert museum is worth a couple of hours. Just enjoy the scenery. Sent from my SM-G892A using Tapatalk
    11 replies | 272 view(s)
  • Handloader109's Avatar
    10-18-2018, 06:30 PM
    Well, I haven't been in the Cabelas here in a month or so. Primers were still less than BP, Won't buy from them.... just too expensive. That is the only real thing I need. Plenty of powder for years, but not so with Primers. Oh well. Need a...
    56 replies | 3150 view(s)
  • Handloader109's Avatar
    10-18-2018, 02:56 PM
    If you are afraid of Win 10's automatic downloading and installing updates, then the one fix i've found is to change your internet to Metered Connection. This will stop all downloads. I've had other folks have major issues with some laser software...
    19 replies | 821 view(s)
  • Handloader109's Avatar
    10-16-2018, 01:13 PM
    I gave up on the 3D printed collator the other day. I just couldn't get it to CONSISTENTLY feed my various 9MM bullets Bottom Down into my Dillon 650 press. If I used one bullet, then maybe, but I use a couple of three and wanted to use for...
    0 replies | 93 view(s)
  • Handloader109's Avatar
    10-16-2018, 10:28 AM
    I haven't hunted in a long while. In MS, my land was annexed a couple of decades ago and they restricted hunting to Bow only. Could have used shotgun, wouldn't have used rifle at all. Too many close neighbors as surroundings had slowly built up. ...
    13 replies | 404 view(s)
  • Handloader109's Avatar
    10-14-2018, 12:10 PM
    PM me her address. I have a wall full of old Science Fiction and a few others genres that I'll pull a box from. Good for her!
    26 replies | 547 view(s)
  • Handloader109's Avatar
    10-13-2018, 01:49 PM
    Handloader109 replied to a thread Hot Sauce Business? in Our Town
    Jaysouth is right, not just about sauce, but a lot of products too. I would make enough for local restaurants that will purchase and farmers market. Forget chains. Maybe a few local groceries that dont charge for spots for locally produced items....
    35 replies | 1075 view(s)
  • Handloader109's Avatar
    10-12-2018, 05:57 PM
    Gone.. thank you. Sent from my SM-G892A using Tapatalk
    1 replies | 111 view(s)
  • Handloader109's Avatar
    10-12-2018, 05:42 PM
    I had 3d Printed the Bullet Collator on the project page a while back. Short (original) feeder, 9mm plate, electronics with motor. I'm keeping the MR. Bullet die, but I'll toss in the long spring if you want it. If you want to tinker, here's...
    1 replies | 111 view(s)
  • Handloader109's Avatar
    10-12-2018, 04:54 PM
    Weekend bump
    24 replies | 1007 view(s)
  • Handloader109's Avatar
    10-12-2018, 11:26 AM
    Handloader109 replied to a thread Help retreving iPad in Our Town
    Coat hanger double Hooks in V would probably work. or extra long gripper if you can see it. Sticky tape probably won't stick well enough. They DO have some metal, but not nearly enough for magnet to pick them up by. Not even enough to move it....
    41 replies | 1507 view(s)
  • Handloader109's Avatar
    10-11-2018, 06:16 PM
    Bass Pro is really pretty crappy operation. Sorry, personal opinion, I've been in the home store, the one at Branson, the one in Independence, MO, and the one in Little Rock. Typical old phart gun store. Someone behind counter who knows beans...
    19 replies | 770 view(s)
  • Handloader109's Avatar
    10-09-2018, 05:15 PM
    Suggestion. If no offers, The auction site that starts with an e has a few guys making anodized aluminum heads for both 550 and 650. About half of Dillons price. And they work fine on my 650 Sent from my SM-G892A using Tapatalk
    2 replies | 271 view(s)
More Activity
About Handloader109

Basic Information

About Handloader109
Location:
NW Arkansas

Statistics


Total Posts
Total Posts
1,266
Posts Per Day
0.72
General Information
Last Activity
Today 02:33 PM
Join Date
01-05-2014
Referrals
0

1 Friend

  1. AmmoMike83 AmmoMike83 is offline

    Boolit Buddy

    AmmoMike83
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check