WidenersRotoMetals2Lee PrecisionMidSouth Shooters Supply
Titan ReloadingGraf & SonsInline FabricationRepackbox

Tab Content
  • gnostic's Avatar
    Today, 10:41 AM
    gnostic replied to a thread Black guns in Factory Rifles
    The $300 AR isn't mil spec. Once you get to mil spec, like Spikes Tactical $1300, I don't think there is a difference. Almost all top brands, are made with Aero Precision parts. A guy on youtube fired a Spikes Tactical 3500 times on full auto, until...
    24 replies | 715 view(s)
  • gnostic's Avatar
    Yesterday, 07:16 PM
    Glock is the Bic Lighter of handguns...
    53 replies | 8988 view(s)
  • gnostic's Avatar
    02-11-2019, 03:19 PM
    I shoot lighter bullets, i.e. 120 grain, .358, 9mm in my .357 revolvers at my steel targets. Heavy bullets have too much thump...
    23 replies | 589 view(s)
  • gnostic's Avatar
    02-09-2019, 02:13 AM
    It's my understanding, the softest bullet that doesn't lead the barrel, will be the most accurate. Also, soft lead is cheaper than lino or wheel weights. I water drop everything so hardness isn't an issue. As long as my bullets are the right size, I...
    15 replies | 463 view(s)
  • gnostic's Avatar
    02-06-2019, 03:19 PM
    Has anyone shot cast bullets from a bolt, or single shot. One of my many theories is, the gas port in the AR's barrel erodes, or otherwise damages the cast bullet before it leaves the muzzle. I've been tempted to try cast bullets in my XP-100, to...
    24 replies | 1502 view(s)
  • gnostic's Avatar
    01-31-2019, 02:32 PM
    I moly all of my jacketed bullets and seal them with Carnauba wax. It keeps the copper fouling at a minimum with high speed bullets like the 220 Swift, 6mm Rem etc. After as few as 10 rounds without moly, copper fouling is present. You can see it...
    12 replies | 397 view(s)
  • gnostic's Avatar
    01-29-2019, 11:10 AM
    gnostic replied to a thread Leaded barrel in Cast Boolits
    Ace Hardware has Chore Boy for under three buck, that's the easy way...
    19 replies | 779 view(s)
  • gnostic's Avatar
    01-26-2019, 09:33 AM
    To begin with Interarmes aren't clones, they're Walther made in America. They, unlike the S&W Walthers retain the original trigger design. My pistol is beautifully made, has a great trigger and shoots lead and jacketed bullets perfectly. It hasn't...
    32 replies | 1028 view(s)
  • gnostic's Avatar
    01-26-2019, 01:49 AM
    I have a stainless Interarms Walther PPK 380 that I shoot surprising well. I load a 90 grain HP bullet to 1100 FPS for my carry ammo and have great confidence in this pistol. Also, they sell for a lot less than $1500...
    32 replies | 1028 view(s)
  • gnostic's Avatar
    01-24-2019, 12:06 AM
    gnostic replied to a thread Stolen Motorcycle in Our Town
    Sorry for your loss. Did they pick it up and carry it away? In mexico, the dealerships chain their new bikes to the floor. I have a lock alarm on my rotor, that make a loud noise if the bike senses movement...
    31 replies | 1588 view(s)
No More Results
About gnostic

Basic Information

About gnostic
Location:
Somewhere over the rainbow...

Statistics


Total Posts
Total Posts
370
Posts Per Day
0.20
General Information
Last Activity
Today 11:11 AM
Join Date
01-04-2014
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check