MidSouth Shooters SupplyRepackboxTitan ReloadingInline Fabrication
Lee PrecisionRotoMetals2ADvertise hereWideners

  • Bent Ramrod's Avatar
    Today, 11:29 AM
    Ditto on the little Lee for big cases. It seems to center better on the outside deburring step than the RCBS type.
    11 replies | 405 view(s)
  • Bent Ramrod's Avatar
    Today, 11:22 AM
    I have one of those moulds. Got a 1-1/2” 100-yd group with my Douglas-rebarreled Krag rifle with 18gr 4759 at ~1550 ft/sec using Lino-WW range scrap. Got a lot of 2-1/2”-3-1/2” groups with other loadings and powders. Pretty much came to the...
    4 replies | 168 view(s)
  • Bent Ramrod's Avatar
    05-31-2020, 10:56 AM
    Ken, didn’t I give you a bunch of old Lakeville Arms literature at the last Denver Gun Show? IIRC, it had a lot of that Prot-X-Bore and Jugular stuff in there.
    14 replies | 1638 view(s)
  • Bent Ramrod's Avatar
    05-29-2020, 06:49 PM
    I follow Dutch Schoultze’s advice—tighten the micrometer thimble down as tight as you can. No “feather touch” here. That’s the patch thickness the ball will see when it is pressing the patch against the rifling, tightly but short of tearing it.
    17 replies | 230 view(s)
  • Bent Ramrod's Avatar
    05-29-2020, 06:15 PM
    You might (assuming that your dies are .22–6mm size) check with Corbin’s and see if he can make you a punch that fits the shellholder slot in your ram. For bigger bullets a solid ram, threaded at the top, would be preferable. An adapter that...
    4 replies | 186 view(s)
  • Bent Ramrod's Avatar
    05-27-2020, 10:08 AM
    I recall seeing a picture of an actual Stevens Maynard in one of Grant’s books. He speculated that it was a toolroom model made at Stevens after they took over Massachusetts Arms, to assess the possibility of manufacturing them at Stevens’ factory....
    22 replies | 593 view(s)
  • Bent Ramrod's Avatar
    05-26-2020, 12:37 AM
    If the excess brass is 1/4” or more, I use a tubing cutter for most of it. Then it’s over to the Universal expander and then the case trimmer. If I have a file/trim die, a hacksaw cut and filing the end smooth.
    18 replies | 333 view(s)
  • Bent Ramrod's Avatar
    05-24-2020, 01:13 PM
    In the 70s, Jensen’s Custom Ammunition used to have bins full of that ammo, mostly unpackaged in bulk. I recall the rims said WCC 60 and R A (forget date). Loaded with a cute little FMP pointed boattail, smeared with lacquer, and some very fine...
    6 replies | 1004 view(s)
  • Bent Ramrod's Avatar
    05-24-2020, 12:38 PM
    I shoot a percussion Sharps replica, Gallagher replica, an original Maynard and a Parker-Hale Volunteer. The Sharps is especially critical, as the cap flash has to go through two right angles and penetrate the back of a paper cartridge to fire. ...
    12 replies | 891 view(s)
  • Bent Ramrod's Avatar
    05-21-2020, 02:04 PM
    He posts on the ASSRA website; handle rodneys.
    8 replies | 527 view(s)
  • Bent Ramrod's Avatar
    05-21-2020, 11:45 AM
    Rodney Storie sells casting sets for the Stevens Tip-Up rifle action. You might see if he has extra castings for the barrel wedge and button. The pivot pin would be best turned and threaded to fit. The wedge casting will need to be spotted and...
    8 replies | 527 view(s)
  • Bent Ramrod's Avatar
    05-20-2020, 08:47 AM
    I had a partial large, old can of 4831 with rust from the inside of the can mixed in with the powder. The powder was otherwise dry and odorless. The inside of the can was rust speckled, but not rusted through. I picked a nice breezy afternoon,...
    41 replies | 2168 view(s)
  • Bent Ramrod's Avatar
    05-15-2020, 11:37 AM
    I can’t imagine this happening with a Ruger, but some of the cheaper Italian clones (the leftovers that are rejected by the name-brand importers and are sold for cheep by the No-Name-os) sometimes have a poor hammer fit against the rear of the frame...
    53 replies | 3582 view(s)
  • Bent Ramrod's Avatar
    05-13-2020, 11:42 AM
    Properly-sized mops on short handles are good for drying chambers after wet patching after firing a black powder cartridge in a match. Wet chambers tend to lengthen the cases on firing. Also, I find a .38 or .32 mop is perfect for getting the...
    22 replies | 754 view(s)
  • Bent Ramrod's Avatar
    05-12-2020, 11:05 AM
    Whenever I’m down to the last couple ounces of my stash of Hi-Vel #2, I find another full can at a gun show somewhere. It’s like a radioactive half-life, or those oil leaks from sunken ships that keep diminishing but still go on forever. Obviously...
    2 replies | 251 view(s)
  • Bent Ramrod's Avatar
    05-04-2020, 11:18 AM
    If I was in the OP’s shoes, I would scrounge the auction sites for a .32 S&W Short Ideal No 1 nutcracker tool in usable condition, for cheep. Lead can be melted in any usable container with a torch or on a fire, and a teaspoon and gloves used to...
    44 replies | 1971 view(s)
  • Bent Ramrod's Avatar
    05-04-2020, 10:42 AM
    The mould may be too hot. I find that scrap lead alloys that form that crystalline surface will sometimes shrink away from the cavity surface like that. The mould may have cooled while you reset your spruce plate, and heated back up again after a...
    20 replies | 1605 view(s)
No More Results
About Bent Ramrod

Basic Information

About Bent Ramrod
Location:
Southern Arizona
Interests:
Guns and Gun Stuff
Occupation:
Happily Retired

Statistics


Total Posts
Total Posts
3,514
Posts Per Day
0.63
General Information
Last Activity
Today 04:52 PM
Join Date
04-04-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check