Inline FabricationLee PrecisionWidenersMidSouth Shooters Supply
Titan ReloadingRepackboxADvertise hereRotoMetals2

  • Bent Ramrod's Avatar
    Today, 04:17 PM
    Pretty much the same for me. I check the base-turned .348 shell for chambering, anneal the neck and shoulder, dry, prime, put in 11 gr Unique and fill to top with Cream of Wheat and press a dab of bullet lube in the mouth to hold it in. Ka-Pow,...
    10 replies | 450 view(s)
  • Bent Ramrod's Avatar
    Today, 11:43 AM
    Bent Ramrod replied to a thread Russian Jr ammo in Rimfire Area
    The steel-case Junior sometimes gives trouble when fired in .22s with light mainsprings, and the Parkerizing or whatever they coated the shells with sometimes gives extraction problems. You just have to try it in your individual gun and see. The...
    7 replies | 353 view(s)
  • Bent Ramrod's Avatar
    Yesterday, 10:15 AM
    The “brass” nipple was likely an Ampco or Treso nipple, of beryllium copper, as BOZ330 mentioned. I have a Volunteer, which is on its first Ampco nipple and I have a Buffalo Arms platinum-lined nipple ($65) waiting in the wings. I sympathize...
    16 replies | 280 view(s)
  • Bent Ramrod's Avatar
    04-06-2020, 03:49 PM
    I fired the blown-out .348 shells today in the Shiloh Sharps with full loads of 80gr Olde Eynsford 1Fg and a Brooks 524gr paper-patched boolit. All the cases that survived the original fireforming with Unique and Cream of Wheat survived this first...
    10 replies | 450 view(s)
  • Bent Ramrod's Avatar
    04-02-2020, 11:19 AM
    I’ve seen a couple 310 decapping dies that have a fat adjustment screw shank with wedding ring stop at the top with the normal skinny rod for the decapper. Haven’t tried them in a CMR die yet, but that might work just for decapping. They show up...
    7 replies | 1164 view(s)
  • Bent Ramrod's Avatar
    03-31-2020, 03:47 PM
    Our state-wide house arrest goes into effect at 5:00 PM today. However, I heard from our Rangemasters that the Guvnor has deemed Gun Stores and Rifle Ranges are “essential.” No argument from me; I think gun shows are “essential,” too, but no joy...
    16 replies | 1496 view(s)
  • Bent Ramrod's Avatar
    03-29-2020, 04:56 PM
    I wonder about the guy or guys who ordered these moulds. But of course, I picked them up, so who am I to wonder? The three-cavity is a nose-pour .38 Keith-style, a base-pour .32 SWC and a gas-checked .25 (whether for rifle or pistol, I don't...
    25 replies | 1015 view(s)
  • Bent Ramrod's Avatar
    03-29-2020, 11:55 AM
    I bought mine because I had found some loading dies and the Ideal 358318 HPGC mould, and wanted to use them. I guess there are worse excuses for buying a rifle. I also figured it would be “practical” in that I could use .38-.357 bullets for...
    8 replies | 1037 view(s)
  • Bent Ramrod's Avatar
    03-28-2020, 07:14 PM
    HCl will take the tarnish off the brass, but will dissolve the zinc out of the alloy at about the same rate. A quick bath in the stuff probably won’t hurt but if you wait for all the tarnish to go away, you might be etching some of the cases too...
    20 replies | 560 view(s)
  • Bent Ramrod's Avatar
    03-27-2020, 03:03 PM
    With Jamison/Captech defunct, the only source of empty .44-77 brass, outside of turned-from-solid cases, is reworked cases, from those with a .50 caliber Winchester base and rim. The cheapest and easiest to find in this group is the .348...
    10 replies | 450 view(s)
  • Bent Ramrod's Avatar
    03-26-2020, 12:06 PM
    I’ve gone to Office Max and Staples with a Thumb Drive and had a pile of pages scanned While-U-Wait. Don’t know much about computers, but if you have the original emails on your hard drives, there should be some kind of App that brings them up by...
    32 replies | 1193 view(s)
  • Bent Ramrod's Avatar
    03-23-2020, 02:45 PM
    Did you buy your rifle used? Just a WAG, but if somebody tried to pull the trigger with the gun on half-cock, and stopped short of actually breaking the sear notches, it could result in bending the half-cock notch wider and bending back the trigger...
    7 replies | 235 view(s)
  • Bent Ramrod's Avatar
    03-23-2020, 11:50 AM
    With pure lead, run your pot hot. Hot enough so the balls turn gray as they cool. I also found that round balls don’t “pressure cast,” for reasons I can’t fathom. Whatever ladle you use, hold it horizontal to the horizontal mould just off the...
    7 replies | 278 view(s)
  • Bent Ramrod's Avatar
    03-23-2020, 11:39 AM
    Plus a buncha Pope Automatics, Schoyens, Ideal Perfections, Mos’s, Darrs, and Paul Jones’s. And much more! A few of us are Gladstone Ganders and the rest of us are Donald Ducks. On the other hand, it could have been a bunch of...
    18 replies | 1601 view(s)
  • Bent Ramrod's Avatar
    03-22-2020, 01:17 PM
    I found a Borchardt military wreck in much worse condition than the one pictured. I patched the wood up as best I could, stained the patches so they matched the grungy brown of the original and let it go at that. The bore was so clogged with...
    40 replies | 3614 view(s)
  • Bent Ramrod's Avatar
    03-22-2020, 12:28 PM
    I have a dual-cavity Lyman marked “358470” which has two .32 caliber Loverin gascheck cavities in it. I can’t find the 358470 number designation in my Lyman CB Handbooks. So I guess it’s a rare “double” factory mistake, both in the number and...
    6 replies | 463 view(s)
  • Bent Ramrod's Avatar
    03-20-2020, 05:45 PM
    Unless they have green or blue-green deposits on them, they should be fine. Enough of the above corrosion will actually eat tiny holes through the brass, and thin the spots that aren’t eaten through. Usually it’s caused by decomposed smokeless...
    15 replies | 936 view(s)
  • Bent Ramrod's Avatar
    03-19-2020, 12:09 PM
    Frankly, I never heard the “whack-a-mole” designation before I started reading Internet forums. If anybody used such a term in the old magazines, books or instructions, I never came across it. My first cartridge reloading experience was a Lee...
    21 replies | 1220 view(s)
  • Bent Ramrod's Avatar
    03-18-2020, 11:57 AM
    Don’t you snap an e-clip into the rimless groove to make the “rim” on the case? I would do that, then fireform with a small powder charge and Cream of Wheat. My usual rule is, dies for going to smaller calibers, expanding mandrel for no more...
    35 replies | 3231 view(s)
  • Bent Ramrod's Avatar
    03-15-2020, 12:51 PM
    I have several of that type of two-cavity mould. Some gun writer (Venturino?) dubbed them “the thinking man’s mould,” because the two different cavities suggested an experimental turn of mind. In practice, I generally find that I’m always...
    25 replies | 1015 view(s)
  • Bent Ramrod's Avatar
    03-13-2020, 09:01 AM
    The meplat will take a #1 drill, 0.228” and still have a little bit of flat before the ogive starts.
    5 replies | 1007 view(s)
More Activity
About Bent Ramrod

Basic Information

About Bent Ramrod
Southern Arizona
Guns and Gun Stuff
Happily Retired


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 04:23 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check