Lee PrecisionMidSouth Shooters SupplyTitan ReloadingRepackbox
WidenersGraf & SonsRotoMetals2StainLess Steel Media
Inline Fabrication
  • Bent Ramrod's Avatar
    Yesterday, 12:09 PM
    The only manufacturer who worried about the smoke from the chambers firing getting into the space between cylinder pin and cylinder and tying it up was issued US Patent 7,613 in 1850 for his efforts in preventing it. The other manufacturers seemed...
    12 replies | 252 view(s)
  • Bent Ramrod's Avatar
    10-01-2018, 09:24 AM
    I think Remington makes it as well. Seems to split fewer cases than the CCI “Fast and Furious” offering. You’re right—a tragically underappreciated cartridge, perfect for pest control on the 5-20 acre “ranchette.”
    11 replies | 349 view(s)
  • Bent Ramrod's Avatar
    09-28-2018, 12:09 PM
    Can you get a screwdriver past the recoil pad to make sure the buttstock is screwed down tight to the action? My 99 is an old wreck originally in .30-30 which I had relined to .25-35. When I took the forend off, I found a strip of shoelace in the...
    23 replies | 710 view(s)
  • Bent Ramrod's Avatar
    09-27-2018, 06:50 PM
    You need to get hold of Jerry Kuhnhausen’s book on repairing and maintaining Colt SAA revolvers. It contains clear instructions and drawings of what happens as the hammer is cocked and how to time the unlocking, carry-up and relocking of the...
    9 replies | 469 view(s)
  • Bent Ramrod's Avatar
    09-27-2018, 06:35 PM
    The Ideal 3118 was the standard Winchester profile for the .32-20. Lyman sells it now as the 311008.
    15 replies | 442 view(s)
  • Bent Ramrod's Avatar
    09-25-2018, 09:33 AM
    You might do well to forget the Soule sight idea and go for one of the Sporting Tang Sights that Distant Thunder and others offer. You loosen the cup, slide it up and/or over to the marks (theirs or yours) that denote POI at 50, 100 or 200 yds, and...
    20 replies | 543 view(s)
  • Bent Ramrod's Avatar
    09-24-2018, 04:47 PM
    Rule-o Numero Uno: Never shoot anonymous reloads. Nunca. I bought 25 jacketed reloads of .45-70 once. They held the maximum charge of (likely) 3031 behind the 350-gr RNSP. All except one, which had the same charge behind the 500-gr RNSP,...
    30 replies | 967 view(s)
  • Bent Ramrod's Avatar
    09-21-2018, 02:34 PM
    Do your rounds chamber OK? I’ve compressed powder (with compression die) in my .38-55 until the bottom of the shells swole and they resembled .38-56s. A trip back through the FLS die and a check that they fit the chamber, and the boolits were...
    28 replies | 782 view(s)
  • Bent Ramrod's Avatar
    09-21-2018, 10:06 AM
    If you have machining skills, a base can be fabricated for a 3/4” Weaver scope using the plugged sightholes on top of the receiver. Even the recoil of the 23C, in .32-20, hasn’t jarred my lash-up mounting loose. Alternately, you can haunt the...
    19 replies | 658 view(s)
  • Bent Ramrod's Avatar
    09-21-2018, 09:43 AM
    If money is no object, a set of tang and globe target sights will solve your problem handily. A scope would be even better, if you have a thousand bucks in the cookie jar. But if you are just starting out, and your range is limited to 100 yards...
    17 replies | 667 view(s)
  • Bent Ramrod's Avatar
    09-18-2018, 09:03 AM
    I had a Low Wall in .218 Bee for a time. As far as I could see, it didn’t do anything that my other Low Wall in .22 Hornet didn’t do just as well, so I unloaded it after the “Bee Experience” was finished. The nominal velocity increase doesn’t...
    20 replies | 585 view(s)
  • Bent Ramrod's Avatar
    09-17-2018, 09:25 AM
    If your rifle’s bore isn’t pitted, check the first inch or so at the muzzle with a lead ball. If the muzzle is blunderbuss shaped from careless cleaning, it will throw keyholes all over the place, and the only solution I’ve found is a reline job. ...
    7 replies | 246 view(s)
  • Bent Ramrod's Avatar
    09-17-2018, 08:59 AM
    I think what the crewman was doing was priming the cylinders with “petrol”. That Le Rhône rotary engine design used the block as a “carburetor” and only had the exhaust valve (“the monosoupape principle,” I think they called it.). The cylinders...
    20 replies | 738 view(s)
  • Bent Ramrod's Avatar
    09-16-2018, 11:22 AM
    Most of my guns were bought used, so I have no idea how many rounds were fired in them. I don’t count the number of rounds fired in either them or the few new ones I have. I keep records of the loads I test for accuracy, which are five shot...
    58 replies | 1508 view(s)
  • Bent Ramrod's Avatar
    09-16-2018, 09:27 AM
    Not wishing to hijack the thread, but, rfd, could you tell us who offers rental paper-patch chamber reamers? I looked through the offerings of White Rock and 4-D, and couldn’t find any mention. Would like to try one in .45-2.1”
    30 replies | 977 view(s)
No More Results
About Bent Ramrod

Basic Information

About Bent Ramrod
Location:
Southern Arizona
Interests:
Guns and Gun Stuff
Occupation:
Happily Retired

Statistics


Total Posts
Total Posts
3,176
Posts Per Day
0.64
General Information
Last Activity
Today 08:35 PM
Join Date
04-04-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check