WidenersRepackboxRotoMetals2MidSouth Shooters Supply
Titan ReloadingADvertise hereInline FabricationLee Precision

Donate Now Goal amount for this year: 6000 USD, Received: 4555 USD (76%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


  • Bent Ramrod's Avatar
    Yesterday, 09:46 AM
    Any slight decomposition of the powder would not, of course, cause the slight rust freckling in the new plastic bottles that one sees in an old metal can. I can’t see any advantage or disadvantage in the storage potential of the metal vs plastic...
    11 replies | 235 view(s)
  • Bent Ramrod's Avatar
    08-10-2020, 11:41 AM
    I’m not an expert on blowups (thank heaven!), but that vastly expanded primer pocket in the still-chambered shell in the Lee barrel says “overload” to me. As well as the bullet not exiting the barrel before the receiver ring let go. Insufficient...
    17 replies | 1990 view(s)
  • Bent Ramrod's Avatar
    08-09-2020, 12:40 PM
    The Chase Patch is strictly a breech-seating benchrest proposition. The rectangular patch wraps once around the boolit and butts square against itself. There is no overlap, nor is there any folding over the boolit base. You curl the patch into...
    12 replies | 363 view(s)
  • Bent Ramrod's Avatar
    08-07-2020, 11:28 AM
    Congratulations! The 23 is a working-class rifle, but a good one. Original magazines are generally pretty expensive, when found, but Triple K made a replacement that at least fits and works. Grinding or filing the sharp corners off the bottom...
    6 replies | 246 view(s)
  • Bent Ramrod's Avatar
    08-06-2020, 10:31 AM
    The jacket spring back may happen when bullet diameters are reduced, but unless you’re a benchrest competitor, it will likely have no effect on the shooting. I had a Remington Model 8 with a 0.260” groove diameter barrel that would throw the...
    13 replies | 293 view(s)
  • Bent Ramrod's Avatar
    08-04-2020, 08:47 PM
    It’s a SAS “Mity-Mite” bullet swaging press. Enormous leverage for swaging, not enough ram travel for reloading. I think the Corbins carried it for a while after they bought out Ted Smith, and then it morphed into the Corbin “Silver” Press.
    3 replies | 171 view(s)
  • Bent Ramrod's Avatar
    08-04-2020, 08:30 PM
    Ideal 457124. Their copy of the standard roundnose military boolit in the original Trapdoor rifle load, and the carbine load. Lyman still makes it.
    5 replies | 195 view(s)
  • Bent Ramrod's Avatar
    07-30-2020, 12:22 PM
    A lot of the old “40-rod” benchrest shooters in Shooting and Fishing like Rabbeth and Chase just poured the powder into the (single) case that they used over and over. However, many of them said they “tapped the case” to settle the powder before...
    17 replies | 536 view(s)
  • Bent Ramrod's Avatar
    07-29-2020, 10:42 AM
    Bent Ramrod replied to a thread 308 in 270 in Factory Rifles
    Marble and Echo used to make broken shell extractors. These had the appropriate sized case head and rim with spring fingers which would go through the case neck and catch on the mouth of the case. Inserting it into the chamber, closing the bolt,...
    31 replies | 1358 view(s)
  • Bent Ramrod's Avatar
    07-26-2020, 10:11 AM
    Corbin offered a short length of metal tube with a hardened, domed washer with his .22 shell swaging die set. The tube fit over the press ram. The assembly traveled up and down with the press ram with the hole in the washer a close fit on the...
    10 replies | 383 view(s)
  • Bent Ramrod's Avatar
    07-14-2020, 11:22 AM
    I have an accumulation of Lyman 45s for general use. I like the looks of them. If you are using the Ideal or the usual Alox-beeswax lubes, and only sizing a thousandth or two, they are fine. Dies and wrenches are easy to get, and switching out...
    18 replies | 1405 view(s)
  • Bent Ramrod's Avatar
    07-14-2020, 10:55 AM
    I have one in .45 caliber and one in .44. I think they are both the “TGBS” type. Workmanship and finish leave nothing to be desired. I put a hex nut on the adjustment screw of the .45 to make doubly sure the adjustment wouldn’t move. There is...
    1 replies | 175 view(s)
No More Results
About Bent Ramrod

Basic Information

About Bent Ramrod
Location:
Southern Arizona
Interests:
Guns and Gun Stuff
Occupation:
Happily Retired

Statistics


Total Posts
Total Posts
3,544
Posts Per Day
0.63
General Information
Last Activity
Today 10:29 AM
Current Activity
Viewing Attachment
Join Date
04-04-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check