Lee PrecisionADvertise hereRepackboxRotoMetals2
Titan ReloadingInline FabricationMidSouth Shooters Supply

  • Bent Ramrod's Avatar
    Yesterday, 11:41 AM
    I like the old stuff as much as anybody, but I would say if he was to sell that press, 99 of 100 prospective buyers would consider what he did was a vast improvement. Especially since he followed through so that the priming function still works. ...
    16 replies | 460 view(s)
  • Bent Ramrod's Avatar
    01-18-2021, 11:41 AM
    Bent Ramrod replied to a thread Vegan Lube in Boolit Lube !
    You might need to make a few experimental mixtures, but some combination of one of the leaf or berry waxes and jojoba oil should give you the right combination of hardness, lubricity and ability to soften black powder fouling, in combination with...
    39 replies | 904 view(s)
  • Bent Ramrod's Avatar
    01-17-2021, 04:38 PM
    I’ve done a fair amount of reworking of Ideal, Lyman and RCBS boolit dies and have yet to find one that can’t be drilled, bored or turned with standard High-Speed tooling. Maybe Star dies are hardened and ground (they look like it) and possibly...
    6 replies | 172 view(s)
  • Bent Ramrod's Avatar
    01-17-2021, 03:56 PM
    You might check with Rodney Storie. He sells sets of castings for many single shot actions. They need fitting and finish machining, but are less work than reproducing the parts from solid stock.
    9 replies | 313 view(s)
  • Bent Ramrod's Avatar
    01-16-2021, 03:04 PM
    Townsend Whelen did a writeup of the Modern-Bond tong tools in one of the Arms And The Man magazines a couple years before the US entry into WWI. I think by then Marlin had gone into war work for the Triple Entente, and had dropped the Ideal line...
    2 replies | 115 view(s)
  • Bent Ramrod's Avatar
    01-16-2021, 01:17 PM
    Shiloh Rifles, C. Sharps Arms or one of the suppliers like Buffalo Arms or Sagebrush ought to have them. Or you could buy a yard of Delrin rod from Professional Plastics or another supplier and make your own.
    16 replies | 489 view(s)
  • Bent Ramrod's Avatar
    01-16-2021, 01:09 PM
    I can only relate to my own experience here. I bought the Corbin .22RF-to-.224 jacketed bullet die set back in the ‘70s, when the kit, including core mould, cost $78. Hornet bullets from the manufacturers could be gotten for $2.50 per hundred at...
    29 replies | 755 view(s)
  • Bent Ramrod's Avatar
    01-16-2021, 11:45 AM
    If it’s just surface rust, I would boil the blocks in water for ten minutes or so. (Longer if you are living above 4000 ft altitude.) This converts the red rust (which tends to go on rusting) to black rust, which is stable, and basically the...
    14 replies | 278 view(s)
  • Bent Ramrod's Avatar
    01-15-2021, 12:11 PM
    The guys who are successful in the swaged bullet business are typically addressing niche markets. A top benchrester like Berger, who shoots his own bullets and wins can parlay his product into a business this way, selling to those who hope to...
    29 replies | 755 view(s)
  • Bent Ramrod's Avatar
    01-14-2021, 11:55 AM
    It’s the 1890 version of the Winchester bullet mould. Earlier versions didn’t have wooden handles. Typically the caliber was stamped on the upper handle between the wood and the mould block. It would say something like “32-165,” For caliber and...
    12 replies | 453 view(s)
  • Bent Ramrod's Avatar
    01-13-2021, 06:59 PM
    A friend of mine got a length of 5/16” (or maybe 3/8”) Delrin rod, whittled a jag tip on the end and used it to clean his Trapdoor from the breech. It’s flexible enough to bend past the action and allow cleaning this way.
    16 replies | 489 view(s)
  • Bent Ramrod's Avatar
    01-12-2021, 01:46 PM
    Except for the use of some of the more modern powders, about all you need to know about all the quasi-standard Lovell variants is covered in C. S. Landis’ .22 Caliber Varmint Rifles. I think Wolfe Publishing has done a reprint, and the original...
    15 replies | 579 view(s)
  • Bent Ramrod's Avatar
    01-12-2021, 12:31 PM
    I will also assume you meant groove diameter 0.458” and that you want bore rather than groove diameter boolits for your paper patching experiments. I just tried a boolit from a Brooks 0.441+” diameter mould that I lapped out to 0.443”, patched...
    4 replies | 163 view(s)
  • Bent Ramrod's Avatar
    01-09-2021, 01:37 PM
    Nickel is typically a thin plating, removable by solutions of persulfate ion. The underlying metal is not appreciably reduced in dimension or fit by this removal. Chromium only comes off (completely) by reverse electrolysis. I’ve seen chrome...
    5 replies | 541 view(s)
  • Bent Ramrod's Avatar
    01-09-2021, 01:06 PM
    Bent Ramrod replied to a thread Black Ideal Lube in Boolit Lube !
    Glad to hear that, GF; I had some memory that certain no-longer-produced rifle actions had been dropped in the latest edition. There’s no greater certainty of finding some weird artifact than after the factory drops support, the reviewers lose...
    33 replies | 871 view(s)
  • Bent Ramrod's Avatar
    01-08-2021, 12:31 PM
    The Vandalia was my first shotshell reloader. It was complete for all three gauges, but I only used the 16-ga attachments, as that was my only shotgun. A query to the American Rifleman got me the information that the reviewers at the time it was...
    6 replies | 265 view(s)
  • Bent Ramrod's Avatar
    01-08-2021, 11:04 AM
    Bent Ramrod replied to a thread Black Ideal Lube in Boolit Lube !
    GF, My copy of the Dell&Schwartz book is the later revision. I seem to recall that they mentioned that they had cut out a lot of “obsolete” material from the first edition, so some of the formulations might have been lost then; also any old...
    33 replies | 871 view(s)
  • Bent Ramrod's Avatar
    01-07-2021, 01:19 PM
    Bent Ramrod replied to a thread Black Ideal Lube in Boolit Lube !
    Colloidal particles are larger than molecules but smaller than one micron in size, typically dispersed (or dispersible) in another phase and difficult or impossible to filter or centrifuge back out. I think I have one lubrisizer with the old...
    33 replies | 871 view(s)
  • Bent Ramrod's Avatar
    01-03-2021, 01:41 PM
    “Dangerous Dave, the Old Western Scrounger.” I used to go to the El Cerrito store when I visited my parents in the Bay Area. The fence around the place was made of rifle barrels and the door knobs were revolver grip frames. There was a lot of...
    14 replies | 982 view(s)
  • Bent Ramrod's Avatar
    01-03-2021, 12:28 PM
    If you have any plans to fire a lot of shots at any one time (like a rifle match), the military style stock and buttplate of the “official” Quigley model with the 2-7/8” chamber will point up any recoil sensitivity you might have pretty quickly. If...
    16 replies | 494 view(s)
  • Bent Ramrod's Avatar
    01-02-2021, 11:13 PM
    Bent Ramrod replied to a thread Pre-owned powder in Our Town
    Earl Naramore’s Principles and Practice of Reloading Ammunition has an extensive section on the working up of charges with unknown powders. This was published in 1954, and no doubt was compiled from notes made during and after WWII, when a given...
    30 replies | 1021 view(s)
  • Bent Ramrod's Avatar
    01-02-2021, 09:15 AM
    I’ve used a couple of cans. It works OK, properly applied, but no better than the smoke from the candles I use for fluxing the melt. It does seem to be harder to remove from the mould than candle soot. Whether this is good or bad depends on...
    36 replies | 1162 view(s)
  • Bent Ramrod's Avatar
    01-01-2021, 11:39 AM
    I bang all the odds&ends of BP substitutes, salvaged black powder from cartridges, and the like in cap&ball pistols. Lots of extra shooting for cheap.
    39 replies | 1094 view(s)
  • Bent Ramrod's Avatar
    01-01-2021, 10:40 AM
    The insides I’d polish with crocus cloth on a stick, just in case. The outsides would get a bath overnight in Liquid Wrench and brushing with a brass wire brush. A wipe with paper towels to get the loose rust off, and any residual crocus out of...
    8 replies | 442 view(s)
  • Bent Ramrod's Avatar
    01-01-2021, 09:48 AM
    Bent Ramrod replied to a thread Pre-owned powder in Our Town
    A copy of Propellant Profiles and a study of the Powder chapter in Sharpe’s Complete Guide to Handloading, supplemented by knowledge of the appearance of the new powders I’ve used previously have always been sufficient background when I’ve bought...
    30 replies | 1021 view(s)
  • Bent Ramrod's Avatar
    12-30-2020, 12:25 PM
    I have one of those as well. Was hoping to use it as a test bed for all the 0.454” conical moulds I’d accumulated, but after bending and having to replace the lever on my cylinder loading tool, I’ve pretty much stuck with 0.452” round balls. The...
    7 replies | 265 view(s)
  • Bent Ramrod's Avatar
    12-27-2020, 01:13 PM
    I have hoarded cans of SR-80 and IMR 1204 that I still dip into from time to time, for nostalgia’s sake. They haven’t been made since the 1930s. I used to buy and use a lot of Pistol #5 and 5744 in my .32-20 revolvers. Every time my cans of...
    22 replies | 1486 view(s)
  • Bent Ramrod's Avatar
    12-27-2020, 12:43 PM
    Corbin sold (and maybe does still) a core mould to go with that .22 RF swage die set. I think BTSniper sells one as well. .22 cast boolits won’t fit in the reformed .22 shell jackets. I’ve always annealed my .22 RF shells by wadding them in a...
    5 replies | 405 view(s)
  • Bent Ramrod's Avatar
    12-25-2020, 11:53 AM
    I’ve only loaded the heel-type boolits in my .380 Rook rifle, but have used both heeled and undersized hollow-based in my .32 Long rifles. The hollow-base boolit is vastly inferior in accuracy to the heeled type, in that caliber anyway. Come to...
    20 replies | 447 view(s)
More Activity
About Bent Ramrod

Basic Information

About Bent Ramrod
Location:
Southern Arizona
Interests:
Guns and Gun Stuff
Occupation:
Happily Retired

Statistics


Total Posts
Total Posts
3,649
Posts Per Day
0.63
General Information
Last Activity
Today 04:00 PM
Join Date
04-04-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check