Titan ReloadingStainLess Steel MediaMidSouth Shooters SupplyInline Fabrication
Graf & SonsWidenersLee PrecisionRotoMetals2

  • Bent Ramrod's Avatar
    Yesterday, 09:03 AM
    I had a Low Wall in .218 Bee for a time. As far as I could see, it didn’t do anything that my other Low Wall in .22 Hornet didn’t do just as well, so I unloaded it after the “Bee Experience” was finished. The nominal velocity increase doesn’t...
    17 replies | 238 view(s)
  • Bent Ramrod's Avatar
    09-17-2018, 09:25 AM
    If your rifle’s bore isn’t pitted, check the first inch or so at the muzzle with a lead ball. If the muzzle is blunderbuss shaped from careless cleaning, it will throw keyholes all over the place, and the only solution I’ve found is a reline job. ...
    6 replies | 156 view(s)
  • Bent Ramrod's Avatar
    09-17-2018, 08:59 AM
    I think what the crewman was doing was priming the cylinders with “petrol”. That Le Rhône rotary engine design used the block as a “carburetor” and only had the exhaust valve (“the monosoupape principle,” I think they called it.). The cylinders...
    20 replies | 557 view(s)
  • Bent Ramrod's Avatar
    09-16-2018, 11:22 AM
    Most of my guns were bought used, so I have no idea how many rounds were fired in them. I don’t count the number of rounds fired in either them or the few new ones I have. I keep records of the loads I test for accuracy, which are five shot...
    52 replies | 869 view(s)
  • Bent Ramrod's Avatar
    09-16-2018, 09:27 AM
    Not wishing to hijack the thread, but, rfd, could you tell us who offers rental paper-patch chamber reamers? I looked through the offerings of White Rock and 4-D, and couldn’t find any mention. Would like to try one in .45-2.1”
    30 replies | 699 view(s)
  • Bent Ramrod's Avatar
    09-06-2018, 05:57 PM
    Wow, that is great stuff! Thanks for posting it. That mould is a great find, too.
    16 replies | 583 view(s)
  • Bent Ramrod's Avatar
    09-06-2018, 05:49 PM
    I don’t trim to length until I’ve fireformed the brass to the chamber, then I try to get as close to 2.100” as I can. (The last setting on the Forster trimmer got me 2.096”, IIRC.). Cases are checked for length after firing and cleaning, and before...
    6 replies | 297 view(s)
  • Bent Ramrod's Avatar
    09-06-2018, 09:04 AM
    With my Chrony, I consider a calm, overcast day “chronograph weather.” If that isn’t in the offing, I wait until the sun is at such an angle so the roof over the line shades the Chrony screens and diffusers. If that isn’t going to happen,...
    7 replies | 258 view(s)
  • Bent Ramrod's Avatar
    09-03-2018, 12:18 PM
    Safety, like any other regulatory program, can become a “growth industry” where more and more strictures are piled on until one can’t do anything, so therefore, one is absolutely Safe. Ken Waters loaded hundreds of smokeless charges in dozens of...
    17 replies | 526 view(s)
  • Bent Ramrod's Avatar
    09-02-2018, 10:57 AM
    My B&M Visible is my primary smokeless powder measure. I have three sheets of settings for various loads of various powders, which get me close for the next charging session. The old Belding and Mull Handbooks also have charge tables for the...
    19 replies | 682 view(s)
  • Bent Ramrod's Avatar
    09-02-2018, 10:24 AM
    Back when I was doing lab work, some of the better pre-electronic dual-pan balances had the pointer index marks on a mirror surface. You could see the reflection of the pointer on the index. If you lined up the pointer so it overlapped the...
    44 replies | 1390 view(s)
  • Bent Ramrod's Avatar
    08-31-2018, 06:29 PM
    There’s a revolver called the Rhino (I believe) that comes in .40 S&W. Not exactly a thing of beauty, and pretty expensive, but it is offered in the caliber. Supposed to be very ergonomic for recoil.
    54 replies | 1758 view(s)
  • Bent Ramrod's Avatar
    08-29-2018, 11:56 AM
    It was paper patch boolits that for me moved the pot thermometer and the lead hardness tester from the “gimmick” column to the “necessary” column in the casting regimen. Whether the thermometer is strictly accurate or not doesn’t matter, as long...
    27 replies | 916 view(s)
  • Bent Ramrod's Avatar
    08-29-2018, 11:31 AM
    Bent Ramrod replied to a thread Help in Our Town
    After my L4-L5 back operation, my doctor tuned me up on Gabapentin. Gave me a big bottle of tiny little capsules of the stuff and told me to start at a certain number, and then increase the intake until the buzzing “asleep” feeling in my foot went...
    22 replies | 638 view(s)
  • Bent Ramrod's Avatar
    08-28-2018, 11:09 AM
    I have a Chargemaster and used it exclusively for a while. It weighs out even coarse powders to +-0.1 gr. It saves work, but doesn’t save me any time. I can trickle up a load on a scale pan as quickly as the Chargemaster can, and at least I’m...
    41 replies | 885 view(s)
  • Bent Ramrod's Avatar
    08-27-2018, 09:30 AM
    I’m going to assume your rifle is a .45-70. Check your cleaning regimen. Bore should be clean and dry for every shot. Check your alloy. Money boolits in particular seem to need harder alloys to keep the noses straight. Start adding...
    27 replies | 916 view(s)
  • Bent Ramrod's Avatar
    08-24-2018, 09:43 AM
    I’ve read pretty nearly every book and Internet article on paper patching, and I still had to make every mistake and follow every red herring for several years before things started coming together. You may notice that all books on paper patching...
    16 replies | 539 view(s)
  • Bent Ramrod's Avatar
    08-22-2018, 09:14 PM
    Ive used a lot of different primers, including FA70 corrosives. No quantum leap in acccuracy one from the other that I’ve found. No Magnum primers or drilled out flash holes, although I think I may have deburred and uniformed the primer pockets on...
    61 replies | 3333 view(s)
  • Bent Ramrod's Avatar
    08-22-2018, 05:03 PM
    Imprimis: An absolutely clean, absolutely dry bore. No matter your cleaning routine, it should look unfired before you load the rifle again. You may get away with a little remaining grunge in the bore after wiping, but then again, you may not. ...
    61 replies | 3333 view(s)
  • Bent Ramrod's Avatar
    08-21-2018, 02:04 PM
    For the commemorative rifle pictured on the side of the box. Another instance of an old-time cartridge case magically showing up after years of absence.
    0 replies | 153 view(s)
No More Results
About Bent Ramrod

Basic Information

About Bent Ramrod
Location:
Southern Arizona
Interests:
Guns and Gun Stuff
Occupation:
Happily Retired

Statistics


Total Posts
Total Posts
3,166
Posts Per Day
0.64
General Information
Last Activity
Today 12:03 PM
Join Date
04-04-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check