Lee PrecisionInline FabricationRotoMetals2Titan Reloading
ADvertise hereMidSouth Shooters SupplyRepackboxWideners

Donate Now Goal amount for this year: 6000 USD, Received: 4555 USD (76%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****

Tab Content
  • ATCDoktor's Avatar
    08-09-2020, 03:43 PM
    I dearly appreciate Savage in 25/20 and have been using it as my primary small game rifle here of late: I was so impressed with the Savage in 25/20 with respect to its accuracy I scoured the earth for one in 32/20 and picked this one up here...
    6 replies | 234 view(s)
  • ATCDoktor's Avatar
    08-03-2020, 10:03 PM
    Neither 32 S&W Long nor 32 S&W short will drop into the magazine opening for either of my Marlin M92’s. The openings on mine would have to be opened up a bit to allow them to fall in.
    31 replies | 726 view(s)
  • ATCDoktor's Avatar
    08-03-2020, 09:25 PM
    You’re gonna need a separate case mouth expander die to load those MBC .311 diameter Bullets. Before I purchased my Lyman “M” die I used this set up for a very short time. Using the brass hammer/claw hammer setup flared case on the...
    16 replies | 397 view(s)
  • ATCDoktor's Avatar
    08-03-2020, 07:06 PM
    Buffalo Arms replenishes their supplies fairly often so if they’re out of stock today usually it’s in stock within a month. That identified, the difference between the two vendors is minimal, Buffalo Arms uses Starline Brass and the last batch I...
    31 replies | 726 view(s)
  • ATCDoktor's Avatar
    08-03-2020, 06:47 PM
    Mine holds a total 14 32 Long Colts and 17 32 Short Colts in the tubular magazine.
    31 replies | 726 view(s)
  • ATCDoktor's Avatar
    08-03-2020, 02:28 PM
    I use 14.5 grains of 4227 and the exact same bullet as the OPs and it gives excellent accuracy And about 1450 fps in my 30/30s.
    16 replies | 397 view(s)
  • ATCDoktor's Avatar
    08-01-2020, 02:11 AM
    Based on what your saying about the dimensions just below the crimp, Id say your crimp is a little too stout and you may be bulging the brass To a point it wont chamber at the point your measuring. I know of no way to correct the issue other...
    9 replies | 260 view(s)
  • ATCDoktor's Avatar
    07-31-2020, 09:56 PM
    The Marlin 1892s are very fine rifles, accurate and Heel based ammo is no harder to kid than any other cartridge. The two I have both came to me with rimfire during pins that were easily replaced with centerfire pins from Jack First and...
    31 replies | 726 view(s)
  • ATCDoktor's Avatar
    07-31-2020, 02:36 PM
    Carbines are awesome and some will shoot very well. This is my Universal and it can be quite accurate but the trigger pull is like 12 pounds. If I could manage that trigger better I bet I coulda centered all ten rounds. Note the 243 round...
    8 replies | 544 view(s)
  • ATCDoktor's Avatar
    07-26-2020, 03:55 PM
    My Savage Sporter came to me with an ancient Weaver J 2.5X scope attached. I had the barrel threaded 1/2X28 and Thompson Machine modify their Zephy 22 LR suppressor to support its use with 25 caliber Bullets. It is one of my favorite rifles...
    11 replies | 449 view(s)
  • ATCDoktor's Avatar
    07-19-2020, 01:18 AM
    The two Im shooting the most are a couple of Marlins: Marlin 1892 chambered in 32 Colt (5 shots off the bench at 100 yards) 5 shots 50 yards offhand
    76 replies | 2966 view(s)
  • ATCDoktor's Avatar
    07-18-2020, 11:33 PM
    Man that’s a neat old revolver. I handload for the 41 long colt and if I had that Remington I’d get on the horn to Old West Bullet Moulds and order their 160 grain 41 heeled based mould (I already have their 41LC crimp die) and go to town...
    8 replies | 289 view(s)
  • ATCDoktor's Avatar
    07-18-2020, 07:38 PM
    Not much help reference the entirety of your question but I shoot it in a couple of Marlin 1894s. I use a 38 special case in my handloads as I was having to seat the bullet way above the crimp groove to get it to cycle in my 357 magnum rifles...
    9 replies | 584 view(s)
No More Results
About ATCDoktor

Basic Information


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 09:20 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check