RotoMetals2Lee PrecisionGraf & SonsStainLess Steel Media
ADvertise hereTitan ReloadingInline FabricationMidSouth Shooters Supply

  • SuperBlazingSabots's Avatar
    06-13-2018, 12:00 PM
    Hello Steve, we face a tough challenge having forced to use sub standard shotshell components for our Heavy Nitro Express needs where we try our level best to help strengthen the components through Nitro cards to be able to withstand our higher...
    657 replies | 222832 view(s)
  • SuperBlazingSabots's Avatar
    06-11-2018, 11:09 AM
    StriperCrazy, most deer are shot between 10 to 40 yards due to heavy brush and 40 or 50 yards being a long shot. You are right-on with your load and...
    14 replies | 626 view(s)
  • SuperBlazingSabots's Avatar
    06-11-2018, 10:50 AM
    All my friends looking to shoot those Heavy 20 gauge Nitro Express loads can buy Beartooth bullets cast .622 bullets for the .600 Nitro Express. In packs or individually. They weigh 1040 gr. My friend Steve wanted me to pass it along to you all,...
    657 replies | 222832 view(s)
  • SuperBlazingSabots's Avatar
    06-09-2018, 01:54 PM
    I just hit a road block with the picture count, here I go with the images meant for the post above ! 16. Polishing your guns forcing cones will definitely help as it has tool marks that the manufacturers failed to polish, its a simple do it...
    657 replies | 222832 view(s)
  • SuperBlazingSabots's Avatar
    06-09-2018, 12:05 PM
    Greetings, When developing newer loads always use newer Fiocchi hull as they tend to show pressure signs early on for safety and once your load is developed switch over to newer Federal hull for hunting for a smoother action when the golden moment...
    97 replies | 28224 view(s)
  • SuperBlazingSabots's Avatar
    06-07-2018, 10:54 AM
    Foam egg cartons, will support the crimp to rest on and not cave-in. Roger I too love a good hard boiled egg salad, you enjoy yours ! At EBay starting .99 cents https://www.ebay.com/i/153017215203?chn=ps&var=452827346494 Want to pay more than:...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-07-2018, 09:50 AM
    Good morning Roger, better yet you can even cut out a round disk from Egg carton of .600 and place it over the RB just for the crimp to get a platform to rest on. Ajay
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-06-2018, 12:04 PM
    Great and as we go we can keep improving, right now all you need is a thin overshot card on top of the RB before crimping, that's it ! ! You can start having fun and do range tests for accuracy, now thats your own cooking make notes and repeat the...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-05-2018, 09:45 AM
    Good Morning Roger, you are getting there and need to keep notes as to how you loaded it. Roger as a friend, never deviate from the load and no matter how much you trust a friend always drop the charge by 2 to three grains then load one shell at...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-04-2018, 07:09 PM
    Roger what you really need is a loader and follow the load exactly as stated and order a selection of nitro cards from Circle Fly, you get double the quantity from them. The Lee Load All does not have a crimp stop either. Any old Lyman easy loader...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-03-2018, 10:28 AM
    Were you paper patching like this where the slug locks-in like this: If wrapped tightly and then folded right it will hold on to the slug till you fire ! ! Ajay Madan Super Blazing Sabots
    29 replies | 793 view(s)
  • SuperBlazingSabots's Avatar
    06-03-2018, 09:31 AM
    Good Morning Roger, please don't start dismantling the loaded hull, keep them aside for now. Ajay Madan
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-02-2018, 08:22 PM
    Hello Roger, The RB needs to come up for the crimp to rest on it. If you just add another .125-20 ga nitro card after the Red OP wad would bring the whole wad column up, that simple. I myself had bought the hand loader in 1970 and even used it...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-02-2018, 03:57 PM
    Hello Roger your last picture shows A. The crimp needs a bit more material to fully close. B. the RB needs yet another .125 nitro card below it or in the base cavity to bring it up to help support the crimp. You are almost there, now. Ajay...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-02-2018, 09:35 AM
    jdfoxinc, please edit your post with the right amount of Lil Gun powder, before someone gets hurt. A lot of shooters come to copy and paste information, have nothing of their own to offer. Thanks. Ajay Madan Super Blazing Sabots
    5 replies | 345 view(s)
  • SuperBlazingSabots's Avatar
    06-02-2018, 09:17 AM
    Roger if you use the hand press then mark the plunger with marker or scotch tape and start crimping a new load and little by little keep marking till you get the desired crimp depth. " Once upon a time " I too had that hand loader. Ajay Madan...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-02-2018, 08:00 AM
    Good morning Roger, once you have the right Fold crimp depth set, leave that setting for next loading session. Adding one more .125-28 ga nitro under the RB in wad will raise the RB in wad for the crimp to rest on top due to RB being smaller in...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-01-2018, 05:41 PM
    The 20 gauge .575 RB load needs to set up like this: Watch the picture carefully and follow. We can't afford to make mistakes. The components that we are using are made for shotshell and not specially made for our " Nitro Express Heavy...
    657 replies | 222832 view(s)
  • SuperBlazingSabots's Avatar
    06-01-2018, 02:35 PM
    Pictures are so important after all we are playing with fire. Please follow the picture. You could put one .125 20 ga nitro card right after the red OP wad followed by .125-28 ga to fill the gap in the base cavity like in the picture. Ajay
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-01-2018, 12:32 PM
    Roger, please no over shot card as the RB would have to roll over it and causing the wad petals to get mangled ! ! Put a .125 nitro card in the wads base cavity instead if need be. In the picture it does not look right the crimp caving in far too...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    06-01-2018, 09:45 AM
    Greetings Roger, welcome back. Pressure is our friend. Higher pressures lead to more consistent, cleaner burning loads with that in mind if your fold crimp is a bit leaning inwards will only help with Higher pressures lead to more consistent,...
    116 replies | 5001 view(s)
  • SuperBlazingSabots's Avatar
    05-30-2018, 05:47 PM
    Hello SilverCreek, can you please post a picture or two of your loaded round, is the RB sticking out of the hull or it is recessed below and how deep? ? Better to be safe than sorry, post some pictures ! ! We are making wild guesses. Thanks....
    7 replies | 265 view(s)
  • SuperBlazingSabots's Avatar
    05-28-2018, 05:38 PM
    Pressure is your friend. Higher pressures lead to more consistent, cleaner burning loads. While fold crimping is far better but your loader must fully help support the hull while crimping. In my 20 ga I had the same problem from time to time and...
    12 replies | 468 view(s)
  • SuperBlazingSabots's Avatar
    05-28-2018, 03:51 PM
    Hello JdFoxInc, http://www.shotgunworld.com/bbs/viewtopic.php?t=120838 Hoping it helps answer your question. Ajay Madan Super Blazing Sabots
    5 replies | 345 view(s)
  • SuperBlazingSabots's Avatar
    05-28-2018, 02:11 PM
    Greetings Moonie, no need to buy the Lyman 5 th as I'll gladly give you those loads and plus: Just don't let this happen its a disaster in my way of thinking: The simple solution: Wad choices for proper fit: Ajay Madan
    4 replies | 297 view(s)
  • SuperBlazingSabots's Avatar
    05-28-2018, 01:53 PM
    Greetings Gpidaho, I would not trim the hull just to fit one particular load instead add a .125" nitro card in the base cavity or under the slug or RB would only help the load. If you choose to trim for that load then mark them to continue to use...
    12 replies | 468 view(s)
  • SuperBlazingSabots's Avatar
    05-27-2018, 01:50 PM
    Hello Y-Man, don't feel bad perhaps even the .662 RB in wad just might do justice to your gun and it simply might be a blessing in disguise. God is great and loves to amaze us every chance he gets. Ajay Madan Super Blazing Sabots
    7 replies | 392 view(s)
  • SuperBlazingSabots's Avatar
    05-26-2018, 09:57 AM
    Y-Man, I think you would benefit from Lyman Foster slug since your barrel beasures .705 the same as the Lyman Foster slug without wad. Do give it a try and might be in for a surprise, never know till you try. In the end we all need to win and put...
    7 replies | 392 view(s)
  • SuperBlazingSabots's Avatar
    05-25-2018, 12:24 PM
    Good Morning, I have been working on the powder identification and could use your help and feed back as to how would you describe these powders, in your way of thinking ? ? **--** If one of you could take the 20 gauge Lyman slug in wad and put...
    657 replies | 222832 view(s)
  • SuperBlazingSabots's Avatar
    05-24-2018, 07:25 PM
    Hello Stripercrazy, Just cut a 3/4 inch photo copy paper strip and wrap it around the ball once in wad, should help. Ajay Madan Super Blazing Sabots
    14 replies | 626 view(s)
More Activity
About SuperBlazingSabots

Basic Information

Statistics


Total Posts
Total Posts
1,207
Posts Per Day
0.36
General Information
Last Activity
Yesterday 08:31 PM
Join Date
05-02-2009
Referrals
0

3 Friends

  1. Glen Heldor Glen Heldor is offline

    Boolit Mold

    Glen Heldor
  2. hatcreek hatcreek is offline

    Boolit Master

    hatcreek
  3. jmort jmort is offline

    Boolit Master

    jmort
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check