ADvertise hereMidSouth Shooters SupplyStainLess Steel MediaTitan Reloading
Graf & SonsLee PrecisionRotoMetals2Inline Fabrication

  • LAGS's Avatar
    04-12-2018, 07:12 PM
    I have taken ODD size screws, and drilled a hole THRU a piece of thin metal shorter than the length threads you will need. Drill the hole in the metal that the screw will barely fit thru. Then I put Johnsons paste wax on the Screw and coat the...
    16 replies | 475 view(s)
  • LAGS's Avatar
    04-01-2018, 08:53 PM
    Bondo, JB Weld or any of the Simpson Construction Epoxies available at Home Depot or Lowes. With Epoxy, use a trowel wet with Denatured Alcohol. Saves a lot of finish sanding.
    16 replies | 480 view(s)
  • LAGS's Avatar
    04-01-2018, 11:20 AM
    I would say that about 60% of the Mauser Receivers that I have rebarreled, especially the older softer Small Rings (with the exception of most of the Sweed's) the bolt lugs were not in Full contact, or one lug only was making contact. Plus a lot...
    29 replies | 724 view(s)
  • LAGS's Avatar
    04-01-2018, 09:40 AM
    Yes , you can remove the barrel and replace it with a Pre threaded short chambered barrel, set the headspace and you are ready to go. But there are really a few more things that should be checked along the way. Like the Bolt Lug engagement, maybe...
    29 replies | 724 view(s)
  • LAGS's Avatar
    04-01-2018, 09:07 AM
    Why Pop the Primers and waste them. I have had similar situations over the years. If in doubt, pull the bullets, drop the load a little and reseat the bullets. But if you dont want to use the Magnum primers for some reason, like the primer cup is...
    36 replies | 1448 view(s)
  • LAGS's Avatar
    03-25-2018, 11:27 AM
    The Super hard is the way to go for most people. But when I bring home 300 lb of lead flashing scrap from one job, I would have to add 60 lb of Super Hard to it to get a 4% antimony ratio. But only have to purchase 12 lb of raw antimony to get the...
    12 replies | 265 view(s)
  • LAGS's Avatar
    03-25-2018, 10:11 AM
    I make my alloys from Raw Materials like pure tin that I buy and Pure Antimony added to the lead I get off construction sites. You have to melt the lead, and add the antimony to the melted lead, Wait a long time like an hour in some cases , plus...
    12 replies | 265 view(s)
  • justingrosche's Avatar
    03-25-2018, 12:16 AM
    I’m looking for a ‘Tender G1 grip to match a forend that I got with this barrel. If you have one to sell, please pm me.Thanks, Justin
    0 replies | 114 view(s)
  • LAGS's Avatar
    03-24-2018, 09:15 PM
    Cedar might be the way to go. At least I will know that Moths will not be eating my barrel. And you guys are correct about the selections of good woods here in Arizona. In my Yard I have two Mesquite trees and an old Jacaranda. Great for nose...
    2065 replies | 503810 view(s)
  • LAGS's Avatar
    03-24-2018, 05:02 PM
    Powdercoat your boolits and the exposed Lube Groove problem goes away. A friend " Armoredman " on this forum has been shooting Cast in his CZ 527 for years, and has had excellent results, with Lubed and PC'ed
    15 replies | 625 view(s)
  • LAGS's Avatar
    03-24-2018, 04:17 PM
    I am thinking about making my own Black powder. I have a question about the charcoal. Has anyone ever tried " Char Cotton " I use to carry a tin of it when I was Back Packing or Hunting , for a fire starter. It would take a a spark way better...
    2065 replies | 503810 view(s)
  • LAGS's Avatar
    03-24-2018, 10:00 AM
    I have a wrench and Barrel Vise, But I am out in east Mesa.
    7 replies | 427 view(s)
  • justingrosche's Avatar
    03-22-2018, 07:36 PM
    It’s in the mail George. Check your PM for the track #.
    10 replies | 369 view(s)
  • justingrosche's Avatar
    03-21-2018, 09:07 PM
    Is this the one your looking for George?
    10 replies | 369 view(s)
  • LAGS's Avatar
    03-20-2018, 07:23 AM
    LAGS replied to a thread Fun old singleshots? in Rimfire Area
    I think he said, An old guy who lived there, moved into a nursing home, and his family threw out a lot of his stuff like the rifle, because it didn't work.
    76 replies | 3472 view(s)
No More Results
About armoredman

Basic Information

About armoredman
Location:
Arizona City

Statistics


Total Posts
Total Posts
1,062
Posts Per Day
0.26
General Information
Last Activity
11-26-2017 05:55 AM
Join Date
04-24-2007
Referrals
1

2 Friends

  1. justingrosche justingrosche is offline

    Boolit Master

    justingrosche
  2. LAGS LAGS is offline

    Boolit Master

    LAGS
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check